User manual PANASONIC TH-50PHD6

[. . . ] ® Operating Instructions PLASMA DISPLAY Progressive Wide Plasma Display ­ MENU INPUT VOL + ENTER POWE R / Y R - STANDB ON G POWER Model No. TH-37PWD6 TH-42PWD6 TH-42PHD6 TH-50PHD6 High Definition Plasma Display Model No. Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference. English TQBC0570 WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: To reduce the risk of electric shock, do not remove cover or back. Refer servicing to qualified service personnel. The lightning flash with arrow-head within a triangle is intended to tell the user that parts inside the product are a risk of electric shock to persons. [. . . ] Refer to the documentation for the computer application for details. Communication parameters Signal level Synchronization method Baud rate Parity Character length Stop bit Flow control RS-232C compliant Asynchronous 9600 bps None 8 bits 1 bit ­ RS-232C Conversion cable Details D-sub 9-pin female RXD 2 3 TXD 5 GND Non use 4·6 7 8 1·9 Shorted NC Basic format for control data The transmission of control data from the computer starts with a STX signal, followed by the command, the parameters, and lastly an ETX signal in that order. If there are no parameters, then the parameter signal does not need to be sent. STX C1 C2 C3 : P1 P2 P3 P4 P5 ETX End (03h) Command Command PON POF AVL AMT IMS Parameter None None Control details Power ON Power OFF Volume 00 - 63 Audio MUTE OFF Audio MUTE ON Input select (toggle) Slot1 input Slot2 input Slot3 input PC input Screen mode select (toggle) NORMAL (4:3) ZOOM FULL JUST Panasonic AUTO ** Start (02h) Colon Parameter(s) (1 - 5 bytes) 3-character command (3 bytes) DAM Notes: (1) If multiple commands are transmitted, be sure to wait for the response for the first command to come from this unit before sending the next command. (2) If an incorrect command is sent by mistake, this unit will send an "ER401" command back to the computer. With the power off, this display responds to PON command only. 0 1 None SL1 SL2 SL3 PC1 None NORM ZOOM FULL JUST SELF 11 Connections AV & COMPONENT Connection COMPONENT VIDEO OUT RR Example of input signal source Y, PB, PR, OUT PB Y DVD L RCA-BNC adapter plug Digital TV-SET-TOP-BOX (DTV-STB) AUDIO R OUT AUDIO HD PR/CR/R PB/CB/B VIDEO IN VIDEO OUT R AUDIO L VD R AUDIO L IN COMPONENT/RGB IN S VIDEO IN AV Y/G SLOT1 SLOT2 SLOT3 PC IN Example of input signal source S VIDEO VCR MONITOR VIDEO IN CAMCORDER VCR L S VIDEO VIDEO R OUT OUT AUDIO OUT Notes: (1) Change the "Component/RGB-in" setting in the "Setup" menu to "Component". (see page 33) (2) Additional equipment, cables and adapter plugs shown are not supplied with this set. RGB signal (R, G, B, HD, VD) Computer RGB Camcorder or VIDEO IN VIDEO OUT R AUDIO L VD HD PR/CR/R PB/CB/B Y/G AV COMPONENT/RGB IN Notes: (1) Change the "Component/RGB-in" setting in the "Setup" menu to "RGB". (see page 33) (2) Additional equipment, cables and adapter plugs shown are not supplied with this set. 12 Power ON/OFF AC cord connection Connecting the AC cord plug to the Plasma Display. Fix the AC cord plug securely to the Plasma Display with the clamper. (See page 9) Power ON/OFF Connecting the plug to the Wall Outlet Press the POWER switch on the Plasma Display to turn the set on : POWER-ON. Power Indicator : Green R - STANDBY G POWER ON INPUT MENU ­ VOL + ENTER R - STANDBY G POWER ON TH-42PWD6 Example: The screen below is displayed for a while after the Plasma Display is turned on. (setting condition is an example. ) Remote Control Sensor From the second time on, the screen shown below is displayed for a while (setting condition is an example). PC NORMAL Power Indicator When the POWER is turned on for the first time, the LANGUAGE selection screen is displayed. From the second time on, language selection can be done from the setup menu. (see page 18) Select the desired language using the and keys and press the ACTION button. OSD LANGUAGE English (UK) Deutsch Fran ais Italiano Espa ol ENGLISH (US) SELECT SET Press the button on the remote control to turn the Plasma Display off. Power Indicator: Red (STAND-BY) INPUT SURROUND Press the button on the remote control to turn the Plasma Display on. Power Indicator: Green To turn the power for the Plasma Display off, press the switch on the Plasma Display, when the Plasma Display is on or in standby mode. Note: During operation of the power management function, the power indicator turns orange in the power off state. VOL N R 13 Basic Controls Main Power On/Off Switch R - STANDBY G POWER ON INPUT MENU ­ VOL + ENTER TH-42PWD6 Enter/Aspect button (see page 16, 19) Remote control MENU Screen ON/OFF Power Indicator sensor Each time the MENU button is pressed, the menu The Power Indicator will light. Indicator not illuminated (The unit will still consume some power as long as the power cord Normal Viewing PICTURE SET UP is still inserted into the wall outlet. ) SOUND PICTURE POS. / SIZE Stand-by . . . . Green (INPUT1, INPUT2, INPUT3 and PC IN Selection) DPMS . . . . . . . . . . . . Orange [With PC input signal and (see page 18) during operation of PC's screensaver. ] Volume Adjustment Volume Up "+" Down "­" C. A. T. S sensor When the menu screen is displayed. Plasma C. A. T. S (Contrast Automatic Tracking System) "+": press to move the cursor up Plasma C. A. T. S automatically senses the ambient light conditions and "­": press to move the cursor down adjusts the brightness and gradation accordingly, to optimise contrast. (Effective when Picture mode is set to Auto. ) (see page 16) Status button Press the "Status" button to display the current system status. 1 PC 1 Input label NORMAL 2 2 Aspect mode (see page 19) N button (see page 20, 21, 22, 23) 3 Off timer The off timer indicator is displayed only when the off timer has been set. [. . . ] 31. 5 kHz 60. 0 Hz Note: Sync cannot be adjusted while a DVI signal is being applied. Setting RGB sync signal Confirm that the input is set to RGB INPUT (this setting is valid only for RGB INPUT signal). H & V: ON G: CS: The H and V sync signals are input from the HD/VD connector. Uses a synchronized signal on the Video G signal, which is input from the G connector. Uses a synchronized signal of Composite Sync input. SYNC H&V SYNC ON G SYNC CS H-FREQ. [. . . ]