User manual PANASONIC TH-50PHW3U

[. . . ] ® High Definition Plasma Display PLASMA DISPLAY Operating Instructions Model No. + ­ INPUT VOL POWE R / Y R - STANDB ON G POWER TH-50PHW3 For assistance, please call : 1-888-VIEW-PTV(843-9788) or send e-mail to : consumerproducts@panasonic. com or visit us at www. panasonic. com (U. S. A) (Puerto Rico) (Canada) For assistance, please call : 787-750-4300 For assistance, please call : 1-800-561-5505 or visit us at www. panasonic. ca Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference. English TQBC0241 WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: To reduce the risk of electric shock do not remove cover or back. Refer servicing to qualified service personnel. The lightning flash with arrow-head within a triangle is intended to tell the user that parts inside the product are a risk of electric shock to persons. [. . . ] Examples of still pictures include logos, video games, computer images, teletext and images displayed in 4:3 mode. 8 Accessories Accessories Supplied Check that you have the Accessories and items shown Operating Instruction book Remote Control Transmitter EUR646525 INPUT Batteries for the Remote Control Transmitter (AA(R6) Battery × 2) SURROUND VOL N R PICTURE SOUND SET UP PICTURE POS. /SIZE ASPECT PC OFF TIMER PLASMA DISPLAY Warranty RCA/BNC Adapter Plug Ferrite core KRCBC160928B Speaker Wire × 2 Optional Accessories · Speakers TY-SP50PHD3W · Pedestal TY-ST42PT1U · Wall stand TY-ST42PW1 · Wall-hanging bracket (angled) TY-WK42PR1 · Connecting Cable TY-SCP15C03 49. 2 ft (15 m) 9 Remote Control Batteries Requires two AA batteries. Install the batteries as shown in the battery compartment. (Polarity + or ­ must match the markings in the compartment). Replace the cove and slide in reverse until the lock snaps. Two "AA" size Helpful Hint: For frequent remote control users, replace old batteries with Alkaline batteries for longer life. Precaution on battery use Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter. Batteries should always be replaced as a pair. Always use new batteries when replacing the old set. Do not combine a used battery with a new one. Do not mix battery types (example: "Zinc Carbon" with "Alkaline"). Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries. Battery replacement is necessary when the remote control acts sporadically or stops operating the Plasma Display. 10 Basic Controls R - STANDBY G POWER ON TH-50PHW3 INPUT ­ VOL + Main Power On/Off Switch Power Indicator The Power Indicator will light. Indicator not illuminated (The unit will still consume some power as long as the power cord is still inserted into the wall outlet. ) Stand-by . . . . Green · · · Input button (VIDEO (S-VIDEO)/COMPONENT, RGB/PC Mode Selection) Push the "INPUT" button to select VIDEO(S-VIDEO)/COMPONENT or RGB/PC input signal modes sequentially. Volume Adjustment Push the Volume Up "+" or Down "­" button to increase or decrease the sound volume level. Stand-by (ON/OFF) button The High Definition Plasma Display must first be plugged into the wall outlet and turn on at the power switch (see page 18). Push this button to turn the High Definition Plasma Display ON, from STANDBY mode. Push it again to turn the High Definition Plasma Display OFF to STANDBY mode. Status button Push the "Status" button to display the current system status. VIDEO NORMAL SURROUND button (see page 27) Input button (VIDEO(S-VIDEO)/COMPONENT, RGB/PC Mode Selection) Press to select VIDEO(S-VIDEO)/ COMPONENT or RGB/PC input signal modes sequentially. (see page 19) INPUT 1 2 Sound mute On/Off (see page 26) Volume Adjustment Press the Volume Up "+" or Down "­" button to increase or decrease the sound volume level. SURROUND OFF TIMER 90 3 VOL 1 VIDEO(S-VIDEO)/COMPONENT, RGB/PC mode 2 Aspect mode (see page 22) 3 Off timer The off timer indicator is displayed only when the off timer has been set. N button (see page 25, 26, 28, 29) N R R button (see page 21, 24, 26, 30) ACTION button Press to make selections POSITION buttons SET UP button (see page 30) SOUND button (see page 26) ASPECT PICTURE SOUND SET UP PICTURE button (see page 28) PICTURE POS. /SIZE PICTURE POS. /SIZE button (see page 24) PC OFF TIMER ASPECT button Press to adjust the aspect. (see page 22) PC button Push the "PC" mode selection button to select the PC mode. OFF TIMER button This button is used to switch The High Definition Plasma Display may be preset to switch to stand-by after a directly to PC mode. The setting changes to 30 minutes, 60 minutes, 90 minutes and 0 minutes (off timer cancelled) each time the button is pressed. [. . . ] ON G: Uses a synchronized signal on the Video G signal, which is input from the G (BNC) connector. ON VIDEO: Compatible with the scart plug (Europe) The composite video signal input from the VIDEO input terminal is used by dividing the sync signals. SYNC H&V SYNC ON G SYNC ON VIDEO Setting PC sync signal setting: Confirm that the input is set to PC INPUT (this setting is valid only for PC INPUT). H&V: The H and V sync signals are input from the HD/VD (BNC) connector. ON G: Uses a synchronized signal on the Video G signal, which is input from the G (BNC) connector. PULL IN RANGE Sets the width for different frequencies. (This setting is the same for both SIGNAL [RGB] and SIGNAL [PC]. ) PULL IN RANGE NARROW CLAMP POSITION Adjusts the clamp position. The following operation methods are the same for "SIGNAL" menu during COMPONENT, RGB and PC input signal mode. [. . . ]