User manual PANASONIC TH-37PA20A

[. . . ] 1 4 7 2 5 8 0 3 6 9 Operating Instructions Progressive Plasma Television Model No. TH-37PA20 TH-42PA20 Pedestal stand shown above is optional extra. Please read these instructions before operating your set and retain them for future reference. English TQBC0696-1 Dear Panasonic Customer Welcome to the Panasonic family of customers. We hope that you will have many years of enjoyment from your new Plasma TV. To obtain maximum benefit from your set, please read these Instructions before making any adjustments, and retain them for future reference. Retain your purchase receipt also, and note down the model number and serial number of your set in the space provided on the rear cover of these instructions. 2 Table of Contents Important Safety Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The system select indicator will change as follows. NZ / INDONES System Select by Regional Sys select NZ / INDONES Australia Region New Zealand, Indonesia, etc. Australia Tuning menu Sys select Auto tuning Manual tuning Fine tuning Skip Australia Australia Off Auto tuning This TV uses auto tuning to determine whether or not the TV can receive a broadcast signal which is being sent. Before Auto tuning, Regional System must already be set. Tuning menu Press to select the "Auto tuning". Press to access to the "Auto tuning". Search Start. 29 Sys select Auto tuning Manual tuning Fine tuning Skip Australia Access Off AUTO SETUP IN PROGRESS SEARCHING : PLEASE WAIT SETUP : Return to tuning menu TV/AV : To exit When a station is found. The best tuning position is automatically memorized. Auto tuning (via front panel) It is also possible to use the control panel buttons on the front of the TV to tune individual programme positions. 1 2 3 AV3 R - STANDBY G - POWER ON STR F / / TV/AV S VIDEO VIDEO L R Press Press Press Press F F (Front panel) until Tuning mode is reached. or / / to access Tuning mode. F (Front panel) to access Auto tune. or / 4 STR F / / TV/AV / to start search. Press at any time to exit the Tuning menu. 18 Tuning Channels Manual tuning Before Manual tuning, Regional System must already be set (see page 18). Press to access to the Manual tuning. Tuning menu Sys select Auto tuning Manual tuning Fine tuning Skip Australia Access Off Press to select the desired Programme Number. Press to select the higher or lower channel. Search Start. 29 Return TV / AV - Exit `STR' Button-Store Programme down/up Search down/up When a station is found. Manual tuning STR When the desired station is found, press to store. The tuning position is memorized. TV/AV Press to exit from the Tuning Menu. This returns the set to the normal viewing condition. Manual tuning (via front panel) It is also possible to use the control panel buttons on the front of the TV to tune individual programme positions. 1 2 3 AV3 R - STANDBY G - POWER ON STR F / / TV/AV S VIDEO VIDEO L R Press Press F (Front panel) until Tuning mode is reached. or / / to access Tuning mode. Press to move between Change programme, Search and Change TV system. TV/AV 4 STR F / / TV/AV Press / or / to change programme position or start search. STR When the desired station is found, press to store. Repeat above procedure to tune additional programme positions. Press F at any time to exit the Tuning menu. Helpful Hint ( (1) / Normalise Normalisation) After the Manual tuning or the Auto tuning is finished, under the normal viewing condition press this button to confirm the tuning condition for each Programme Number. If some Programme Numbers are unused (no TV stations), it is possible to skip such Programme Numbers. Please refer to the Programme Number Skip operation on page 21. (2) When using a VCR without video and audio input/output terminals, it is convenient to connect the aerial cable as indicated in the instruction manual of VCR and to set the designated channel to programme No. In that case, perform manual tune after setting the colour system and sound system in advance. [. . . ] Type of broadcast Mode Indicator Regular broadcast (Standard Audio) No Indicator BILINGUAL or DUAL MONO: MAIN I / SUB II I II STEREO Notes: · If the stereo signal is poor or the receiving conditions are not optimum or if STEREO:MONO automatic switching occurs, it is recommended you switch from STEREO to MONO. · Even when the contents of the receiving signal undergo changes, selection mode is kept intact. · When the receiving conditions deteriorate, listening will be easier if the mode is set to the "MONO" position, using the stereo/bilingual sound selection button. · "DUAL", also known as "DUAL MONO" or as "BILINGUAL" is not currently transmitted in some countries. VCR / DVD Control The Remote Control is capable of operating some functions of selected VCRs and DVD (Digital Versatile Disc) equipment. [. . . ]