User manual PANASONIC TH-37PV7P

[. . . ] Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households) This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, please take these products to designated collection points, where they will be accepted on a free of charge basis. Alternatively, in some countries you may be able to return your products to your local retailer upon the purchase of an equivalent new product. Disposing of this product correctly will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. [. . . ] 27) Reduces brightness of picture to economise on power consumption (Off / On) Increases the brightness of the side panel (Off / Low / Mid / High) The recommended setting is "High" to prevent panel "image retention" Advanced · · · · · · · · Labels or skips each input terminals (p. 28) Sets how long the information banner (p. 15) stays on screen 0 (No display) to 10 sec. increments Sets to use VIERA Link functions (Off / On) (p. 32) Changes the image processing of the panel (depending on the input signal) (50Hz / 100Hz) Set to "100Hz" normally Displays the software licence information Displays the system information of this TV Adjusts volume of individual channel or input mode Select stereo / monaural (Mono / Stereo) Normally: Stereo Stereo signal cannot be received: Mono M1 / M2: Available while mono signal is transmitted Select to fit the input signal (Auto / Digital / Analogue) (p. 31) Auto : Automatic detection of digital or analogue sound source Digital : HDMI cable connection Analogue : HDMI-DVI adapter cable connection HDMI input mode only Press the OK button to reset the present Sound Mode to the default settings HDMI Input Reset to Default 22 · Only available items can be selected. 23 Editing and Setting Channels The current channel settings can be changed according to your needs and reception conditions. INPUT ASPECT EXIT 1 2 3 4 Display the menu MENU Edit the programme position settings Select the channel to edit Programme Edit Prog. Colour Sys. 1 2 3 4 5 CH33 CH21 CH21 CH60 CH21 456 123 XYZ FTP SC1 SC1 SC1 SC1 SC1 Auto Auto Auto Auto Auto · select Channel To change channel number "Manual Tuning" Name 3 FTP CH05 SC1 PAL Corontation Street OK MENU RETURN Select "Setup" Main Menu VIERA Link Picture Cursor access To delete Edit channels Edit red red OPTION DIRECT TV REC After confirming, press green 1 4 7 2 5 8 0 VCR 3 6 9 Sound Setup select To add After confirming, press green yellow yellow Select "Tuning Menu" Setup Menu 1/2 access TEXT F. P. REC INDEX HOLD VCR DVD Q-Link Settings Child Lock Tuning Menu Off Timer Language Teletext Shipping Condition Power Save Side Panel Access Off FLOF Off Off select Delete Add Move Change name Change sound system Change colour system Programme Edit To move Select new position To change the name of the broadcaster displayed when selecting channels Programme Edit Prog. Colour Sys. 1 2 3 4 5 CH33 CH21 CH21 CH60 CH21 456 123 XYZ FTP SC1 SC1 SC1 SC1 SC1 Auto Auto Auto Auto Auto · Editing and Setting Channels Select the "Name" field red Enter the "User input" mode Select the character Set (Maximum: five characters) PROGRAMME Select a function Tuning Menu access Access Access Access RETURN Store Select the "Sound Sys. " field Select sound system SC1 : SC2 : SC3 : F: PAL B, G, H / SECAM B, G PAL I PAL D, K / SECAM D, K SECAM L / L' To return to TV EXIT Auto Setup Programme Edit Manual Tuning To change sound system based on signals Programme Edit Prog. Colour Sys. 1 2 3 CH33 CH21 CH21 CH60 CH21 456 123 XYZ FTP SC1 SC1 SC1 SC1 SC1 Auto Auto Auto Auto Auto 4 5 select 5 Auto Setup Set To change colour system based on signal Automatically set the channels received in the area. 26) has been set, it must be entered. · Normally, select "Auto" CH33 CH21 CH21 CH60 CH21 456 123 XYZ FTP SC1 SC1 SC1 SC1 SC1 Auto Auto Auto Auto Auto Advanced Programme Edit Prog. Colour Sys. 1 2 3 4 Select the "Colour Sys. " field Select colour system Start Auto Setup All tuning data will be erased Start Auto Setup EXIT RETURN Settings are made automatically Auto Setup Scan Channel CH 29 CH 33 Service Name 2 78 1 41 5 Set channels automatically Auto Setup · · · · This will take about 3 mins. All previous settings are erased. The settings are downloaded to a Q-Link compatible equipment connected to the TV. When the operation is completed, the broadcast of programme number "1" will appear. If tuning has not done completely "Manual Tuning" Fine Tuning Set channels manually Manual Tuning Manual Tuning Manual Tuning Programme Fine Tuning Manual Tuning 1 2 Use to make small adjustments to the tuning of an individual channel (affected by weather conditions, etc. ) Set channel manually after Auto Setup. If a VCR is connected with only the RF cable, select programme position "0". [CH33] 78 1 41 For Auto Setup, using the buttons on the front of the TV Press repeatedly until "Auto Setup" appears Access "Auto Setup" Start "Auto Setup" Select the programme position 1 4 2 5 8 0 VCR Select the channel Search and store search store 3 6 9 To return to TV 7 24 25 Control Channel Audience You can lock specific channels and control who watches them. (When a channel is selected, a message appears; by entering the PIN number, you can watch the channel. ) INPUT ASPECT EXIT Restore Settings Resets the TV to its original condition, i. e. All settings (channels, picture, sound quality, etc. ) are reset. 1 2 3 Display the menu MENU INPUT ASPECT EXIT 1 OK MENU RETURN Display the menu MENU OK MENU RETURN Select "Setup" Main Menu VIERA Link Picture access OPTION DIRECT TV REC 1 4 7 2 5 8 0 VCR 3 6 9 Sound Setup select OPTION DIRECT TV REC 2 3 Select "Setup" Main Menu VIERA Link Picture access 1 2 5 8 0 VCR 3 6 9 Sound Setup select Select "Child Lock" Setup Menu 1/2 4 access 7 ·· TEXT F. P. REC INDEX HOLD VCR DVD PROGRAMME Q-Link Settings Child Lock Tuning Menu Off Timer Language Teletext Shipping Condition Power Save Side Panel Select "Shipping Condition" Setup Menu 1/2 Restore Settings Control Channel Audience Access Off FLOF Off Off TEXT F. P. REC access select INDEX HOLD VCR DVD To return to TV EXIT 4 Child Lock-PIN Entry PROGRAMME Q-Link Settings Child Lock Tuning Menu Off Timer Language Teletext Shipping Condition Power Save Side Panel Off FLOF Access Off Off select Set To return to TV EXIT 1 of 2 Enter the PIN number (4 digits) 1 4 **** 2 5 8 0 VCR 3 6 9 Please enter new PIN PIN 7 Select "Service List" Child Lock · · access select select set 4 Set Enter the PIN number twice at first setting. Make a note of the PIN number in case you forget it. Advanced Check the message and initialise Shipping Condition Control channel audience Child Lock Change PIN Service List Access Select the channel to be locked Child Lock Service List Wed 12/05/04 10:46 1 7 14 70 72 80 85 90 Service Name BBC THREE E4 CBBC Nwk BBCi Radio Cymru Lock · · · To cancel Select the locked channel To lock all channels Restore Settings Shipping Condition All tuning data will be erased Are you sure?Are you sure? Confirm EXIT RETURN set yellow blue Follow the on-screen instructions Appears when the channel is locked To change the PIN number Select "Change PIN" in To cancel all channel locks and enter a new PIN number twice. To re-tune TV channels only, e. g. [. . . ] Check all required SCART cables and connections are firmly in place. Direct TV record / Q-Link functions not recording Please confirm SCART cable and connection. Also please set "AV1 / AV2 out" in the Setup Menu (p. 23). Specifications TH-37PV7P Power Source Power Consumption Display panel Average use Standby condition Aspect Ratio Visible screen size Number of pixels Speaker Audio Output AC 220-240 V, 50 / 60 Hz 241 W 0. 7 W 16:9 94 cm (diagonal) 819 mm (W) × 457 mm (H) 106 cm (diagonal) 922 mm (W) × 518 mm (H) 127 cm (diagonal) 1, 106 mm (W) × 622 mm (H) 261 W 364 W 0. 5 W TH-42PV7P TH-50PV7P Permanently lit spots on screen Due to production process involved in this technology this may result in some pixels which are permanently lit or unlit. This is not a malfunction. Auto aspect Auto aspect is designed to provide you with the best aspect ratio to use to fill your screen. [. . . ]