User manual PANASONIC TH-37PWD3UZ

[. . . ] ® Wide Plasma Display PLASMA DISPLAY Operating Instructions Model No. + -- INPUT VOL POWE R / BY R - STAND ON G POWER TH-37PWD4 Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference. English TQBC0337 WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: To reduce the risk of electric shock do not remove cover or back. Refer servicing to qualified service personnel. The lightning flash with arrow-head within a triangle is intended to tell the user that parts inside the product are a risk of electric shock to persons. [. . . ] Do not mix battery types (example: "Zinc Carbon" with "Alkaline"). Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries. Battery replacement is necessary when the remote control acts sporadically or stops operating the Plasma Display. 10 Basic Controls R - STANDBY G POWER ON TY-42PWD4 INPUT ­ VOL + Main Power On/Off Switch Power Indicator The Power Indicator will light. Indicator not illuminated (The unit will still consume some power as long as the power cord is still inserted into the wall outlet. ) Stand-by . . . . Green · · · Input button (VIDEO (S VIDEO)/COMPONENT, RGB/PC Mode Selection) Push the "INPUT" button to select VIDEO(S VIDEO)/COMPONENT or RGB/PC input signal modes sequentially. Volume Adjustment Push the Volume Up "+" or Down "­" button to increase or decrease the sound volume level. Stand-by (ON/OFF) button The Plasma Display must first be plugged into the wall outlet and turned on at the power switch (see page 18). Push this button to turn the Plasma Display ON, from STANDBY mode. Push it again to turn the Plasma Display OFF to STANDBY mode. Status button Push the "Status" button to display the current system status. VIDEO NORMAL SURROUND button (see page 27) Input button (VIDEO(S VIDEO)/COMPONENT, RGB/PC Mode Selection) Press to select VIDEO(S VIDEO)/ COMPONENT or RGB/PC input signal modes sequentially. (see page 19) INPUT 1 2 Sound mute On/Off (see page 26) Volume Adjustment Press the Volume Up "+" or Down "­" button to increase or decrease the sound volume level. SURROUND OFF TIMER 90 3 VOL 1 VIDEO(S VIDEO)/COMPONENT, RGB/PC mode 2 Aspect mode (see page 22) 3 Off timer The off timer indicator is displayed only when the off timer has been set. N button (see page 25, 26, 28, 29) N R R button (see page 21) ACTION button Press to make selections POSITION buttons SET UP button (see page 20) SOUND button (see page 26) ASPECT PICTURE SOUND SET UP PICTURE button (see page 28) PICTURE POS. /SIZE PICTURE POS. /SIZE button (see page 24) PC OFF TIMER ASPECT button Press to adjust the aspect. (see page 22) PC button Push the "PC" mode selection button to select the PC mode. OFF TIMER button This button is used to switch The Plasma Display may be preset to switch to stand-by after a fixed period. setting changes to 30 minutes, 60 minutes, 90 minutes and 0 minutes (off timer cancelled) each time the button is pressed. 30 60 90 When three minutes remain, "Off timer 3" will flash. The off timer is cancelled if a power interruption occurs. 0 11 Connections SPEAKER Terminals (R) SPEAKER Terminals (L) ­ Cable fixing bands Secure any excess cables with bands, as required. Pass the attached cable fixing band through the clip as shown in the figure. To secure cables connected to Terminals, wrap the cable fixing band around them then pass the pointed end through the locking block, as shown in the figure. 1 To tighten: 2 To loosen: Push the catch Pull Pull AUDIO R AUDIO L VIDEO S VIDEO R AUDIO L VD HD PR/CR/R PB/CB/B Y/G AV IN COMPONENT/RGB IN PC IN SERIAL AV IN Terminals (see page 13, 14) COMPONENT/RGB IN and Audio IN Terminals (see page 15) From EXIT monitor Terminal on Computer (see page 16) From SERIAL Terminal on Computer (see page 17) 12 Connections Speakers connection When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker's Installation Manual for details on speaker installation. 1 Speakers (Optional accessories) 2 1 2 AV Input Terminals connection Connect the signal source equipment (see page 14 to 17). (Example) When connecting an S VIDEO VCR (S VIDEO VCR) R Audio OUT L Video OUT S Video OUT S VIDEO 4 pin socket Luminance earth Chrominance earth 2×RCA audio cables AUDIO Audio input to L/R sockets S VIDEO Video input to S VIDEO socket Luminance in Chrominance in R AUDIO L VIDEO S VIDEO AV IN Note: Additional equipment and cables shown are not supplied with this set. 13 Connections AV Input connection VIDEO signal connection (VCR) R Audio OUT L Video OUT AUDIO-VIDEO Video input to RCA socket 3×RCA audio video cables Audio input to L/R sockets R AUDIO L VIDEO S VIDEO AV IN Note: Additional equipment and cables shown are not supplied with this set. COMPONENT/RGB Input connection Component signals (Y, PB, PR) connection (DVD Player) Y Y, PB, PR PB PR 3×RCA video cables AUDIO 2×RCA audio cables L R R AUDIO L VD HD PR/CR/R PB/CB/B Y/G COMPONENT/RGB IN Notes: (1) Change the "COMPONENT/RGB-IN" setting in the "SET UP" menu to "COMPONENT". (see page 37, 39) (2) Additional equipment, cables and adaptor plugs shown are not supplied with this set. 14 Connections RGB signal (R, G, B, HD, VD) connection RGB input to R, G, B, HD, VD sockets Example of input signal source HDTV-compatible VCR BNC-RCA adaptor plug 5×BNC RGB cables RGB camera R AUDIO L VD HD PR/CR/R PB/CB/B Y/G COMPONENT/RGB IN AUDIO 2×RCA audio cables Audio input to L/R sockets Computer VD HD R B G Notes: (1) Change the "COMPONENT/RGB-IN" setting in the "SET UP" menu to "RGB". [. . . ] Press to adjust. SIGNAL CLAMP POSITION [ COMPONENT ] SIGNAL SYNC PULL-IN RANGE CLAMP POSITION [ RGB ] H&V NARROW The following operation methods are the same for both the SIGNAL [RGB] and SIGNAL [PC]. SIGNAL SYNC PULL-IN RANGE CLAMP POSITION [ PC ] H&V NARROW SYNC Setting RGB sync signal Confirm that the input is set to RGB INPUT (this setting is valid only for RGB INPUT). H&V: The H and V sync signals are input from the HD/VD connector. ON G: Uses a synchronized signal on the Video G signal, which is input from the G connector. ON VIDEO: Compatible with the scart plug (Europe) The composite video signal input from the VIDEO input terminal is used by dividing the sync signals. SYNC H&V SYNC ON G SYNC ON VIDEO Setting PC sync signal Confirm that the input is set to PC INPUT (this setting is valid only for PC INPUT). [. . . ]