User manual PANASONIC TH-37PWD4

[. . . ] The lightning flash with arrow-head within a triangle is intended to tell the user that parts inside the product are a risk of electric shock to persons. The exclamation point within a triangle is intended to tell the user that important operating and servicing instructions are in the papers with the appliance. WARNING : To prevent damage which may result in fire or shock hazard, do not expose this apparatus to rain or moisture. Do not place containers with water (flower vase, cups, cosmetics, etc. ) above the set. (including on shelves above, etc. ) WARNING : 1) To prevent electric shock, do not remove cover. [. . . ] AUTO SETUP Automatically adjust H-POS / V-POS / CLOCK PHASE / DOT CLOCK and set H-SIZE / V-SIZE the standard value when RGB signal is input. Notes: · If the dot clock frequency is 108 MHz or higher, DOT CLOCK cannot be made. · If the image is that the edge is hardly figured out or shadowy, that cannot be adjusted automatically. In such case, press AUTO SETUP again after changing the image to the clearer one. · When DVI-D is input, CLOCK PHASE cannot be adjusted automatically. /SIZE and press the ACTION ( ) button when appropriate adjustment cannot be made. V-POS Adjust the vertical position. H-POS H-SIZE V-POS V-SIZE DOT CLOCK CLOCK PHASE 0 0 0 0 0 0 H-POS H-SIZE Adjust the horizontal size. V-SIZE Adjust the vertical size. DOT CLOCK CLOCK PHASE (During "COMPONENT", "RGB" and "PC" input signal) Periodic striped pattern interference (noise) may occur when a striped pattern is displayed. If this happens, adjust so that any such noise is minimized. (During "COMPONENT", "RGB" and "PC" input signal) Eliminate the flickering and distortion. Helpful Hint ( / NORMALIZE Normalization) While the POS. /SIZE display is active, if either the N button on the remote control is pressed at any time or the ACTION ( ) button is pressed during "NORMALIZE", then all adjustment values are returned to the factory settings. 21 PICTURE Adjustments 1 2 Press to display the PICTURE menu. Select to adjust each item. Select the desired level by looking at the picture behind the menu. Note: BASS, MID, TREBLE and SURROUND settings are memorized separately for each AUDIO MENU. Helpful Hint ( / NORMALIZE Normalization) While the "SOUND" menu is displayed, if either the N button on the remote control is pressed at any time or the ACTION ( ) button is pressed during "NORMALIZE", then all adjustment values are returned to the factory settings. 24 PRESENT TIME SETUP / SET UP TIMER The timer can switch the Plasma Display ON or OFF. Before attempting Timer Set, confirm the PRESENT TIME OF DAY and adjust if necessary. Then set POWER ON TIME / POWER OFF TIME. 1 2 SET UP 2/2 Press to display the SET UP menu. Press to select SET UP TIMER or PRESENT TIME SETUP. SET UP TIMER PRESENT TIME SETUP Press to display the SET UP TIMER screen or PRESENT TIME SETUP screen. PRESENT TIME SETUP 1 Press to select DAY or PRESENT TIME OF DAY. PRESENT TIME SETUP PRESENT TIME OF DAY MON 99:99 Press to set up DAY or PRESENT TIME OF DAY. SET button: Forward MON DAY button: Back 99:99 PRESENT TIME OF DAY Notes: · Pressing " " or " " button once changes PRESENT TIME OF DAY 1 minute. · Pressing " " or " " button continuously changes PRESENT TIME OF DAY by 15 minutes. 2 Press to select SET. Notes: · SET cannot be selected unless PRESENT TIME OF DAY is set. · Unless setting the present time other than "99:99", DAY setting is invalid. · The settings of "DAY" and "PRESENT TIME OF DAY" are reset when leaving the display turned off for about 7 days for the following reasons: Pressing POWER switch of the unit to turn off the display. Interruption of power supply. SET UP TIMER 1 Press to select POWER ON TIME / POWER OFF TIME. Press to set up POWER ON TIME / POWER OFF TIME. [. . . ] For products requiring routine preventive maintenance, that maintenance must be performed in order to maintain warranty coverage. Serial numbers that have been altered, defaced or removed void this warranty. This warranty does not cover replacements or repairs necessitated by loss or damage resulting from any cause beyond the control of PCI. Marking or retained images (sometimes called "burn-in") resulting from the display of fixed images on video display products are not defects and are not covered under this warranty. [. . . ]