User manual PANASONIC TH37PWD5CZ

[. . . ] Visit our Panasonic Web Site http://panasonic. net Table of Contents Important Safety Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Accessories Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · If Auto Setup cannot adjust correctly, select "Normalise" once and press ACTION ( ), then adjust Pos. /Size manually. V-Pos Adjust the vertical position. H-Size Adjust the horizontal size. V-Size Adjust the vertical size. Dot Clock (During Component/PC input signal) Periodic striped pattern interference (noise) may occur when a striped pattern is displayed. If this happens, adjust so that any such noise is minimized. (During Component/PC input signal) Eliminate the flickering and distortion. (During Component/PC input signal) Adjusts the clamp position when black parts of the image have no detail due to underexposure or are tinged with green. Optimum value for Clamp Position adjustment When black parts have no detail due to underexposure (blackout) Value that causes least blackout is the optimum. When black parts are tinged with green Value that cancels the greenishness without causing blackout is the optimum. Clock Phase Clamp Position Over scan Turn image over scan On/Off. Configurable signals are as follows: 525i, 525p, 625i, 625p, 750/60p, 750/50p, 1125/60i, 1125/50i, 1125/24sF, 1125/25p, 1125/24p, 1125/60p, 1125/50p, 1125/30p (Component Video, RGB, DVI, HDMI) On Off Notes: · When "Off" is set, "H-Size" and "V-Size" cannot be adjusted. · When the "Display size" is set to "On" in the Options menu, this setting will be invalid. (see page 42) Helpful Hint ( / Normalise Normalisation) While the Pos. / Size display is active, if either the N button on the remote control is pressed at any time or the ACTION ( ) button is pressed during "Normalise", then all adjustment values are returned to the factory settings. 22 Picture Adjustments 1 2 Press to display the Picture menu. Select to adjust each item. Select the desired level by looking at the picture behind the menu. Steps 1 and 2 affect each other's settings, so repeat each step in turn to make the adjustment. · The adjustment values are memorized separately for each input terminal. · The adjustment range values should be used as an adjustment reference. Helpful Hint ( / Normalise Normalisation) On the remote control unit, while the "Advanced settings" menu is displayed, if either the N button is pressed at any time or the ACTION ( ) button is pressed during "Normalise", then all adjustment values are returned to the factory settings. 24 Sound Adjustment 1 2 Press to display the Sound menu. Select the desired level by listening to the sound. Sound Normalise Normal Sound Mode Bass Treble Balance Normal 0 0 0 3 Item Sound Mode Bass Treble Balance Press to exit from adjust mode. Details Normal: Emits the original sound. Adjusts left and right volumes. Note: Bass and Treble settings are memorized separately for each Sound Mode. Helpful Hint ( / Normalise Normalisation) While the "Sound" menu is displayed, if either the N button on the remote control is pressed at any time or the ACTION ( ) button is pressed during "Normalise", then all adjustment values are returned to the factory settings. 25 Screensaver (For preventing image retention) Do not display a still picture, especially in 4:3 mode, for any length of time. If the display must remain on, a Screensaver should be used. 1 2 Setup 1/2 Press to display the Setup menu. Press to display Screensaver screen. Signal Screensaver Extended life settings Input label Component/RGB-in select Power save PC Power management DVI-D Power management No signal power off No activity power off OSD Language RGB Off Off Off Disable Enable English (UK) 3 Function selection Press to select Function. Negative image Scrolling bar only White screen Overlay scrolling bar Negative image Scrolling bar only Overlay scrolling bar White screen Screensaver Start Function Mode Scrolling bar only Off : Negative image will be displayed on the screen. : A white bar will scroll from left to right. : The brightness of the image will be decreased and a white bar will scroll on it. [. . . ] The top and bottom edges of the pictures are cut off. The letterbox pictures with a 2. 35:1 aspect ratio among the 16:9 aspect ratio signals are enlarged vertically and horizontally so that their display fills the screen. The top and bottom edges as well as the left and right edges of the pictures are cut off. Letterbox pictures with a 2. 35:1 aspect ratio are enlarged vertically and horizontally so that their display fills the screen vertically and is slightly larger than the screen horizontally. [. . . ]