User manual PANASONIC TH-37PWD5UZ

[. . . ] ® PLASMA DISPLAY Progressive Wide Plasma Display Operating Instructions + -- INPUT VOL POWE R / BY R - STAND ON G POWER Model No. TH-37PWD5 Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference. English TQBC0433-1 WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: To reduce the risk of electric shock, do not remove cover or back. Refer servicing to qualified service personnel. The lightning flash with arrow-head within a triangle is intended to tell the user that parts inside the product are a risk of electric shock to persons. [. . . ] Battery replacement is necessary when the remote control acts sporadically or stops operating the Plasma Display. 9 Basic Controls R - STANDBY G POWER ON INPUT -- VOL + Main POWER ON/OFF Switch TH-37PWD5 Remote control sensor Power Indicator The Power Indicator will light. POWER-OFF Indicator not illuminated (The unit will still consume some power as long as the power cord is inserted into the wall outlet. ) STAND-BY . . . . . Red POWER-ON. . . . . Green · · · INPUT button (VIDEO (S VIDEO), COMPONENT/RGB and PC Mode Selection) (see page 19) VOLUME Adjustment Press the Volume Up "+" or Down "­" button to increase or decrease the sound volume level. STAND-BY(ON/OFF) button The Plasma Display must first be plugged into the wall outlet and turned on at the power switch. (see page 18) Press this button to turn the Plasma Display ON, from STAND-BY mode. Press it again to turn the Plasma Display OFF to STAND-BY mode. STATUS button Press the "STATUS" button to display the current system status. VIDEO NORMAL C. A. T. S sensor Plasma C. A. T. S (Contrast Automatic Tracking System) Plasma C. A. T. S automatically senses the ambient light conditions and adjusts the brightness and gradation accordingly, to optimise contrast. (Effective when Picture mode is set to Auto. ) SURROUND button (see page 27) INPUT button (VIDEO(S VIDEO), COMPONENT/ RGB, PC Mode Selection) Press to select VIDEO(S VIDEO), COMPONENT/RGB, PC input signal modes sequentially. (see page 19) INPUT 1 2 Sound mute On/Off (see page 26) VOLUME Adjustment Press the Volume Up "+" or Down "­ " button to increase or decrease the sound volume level. SURROUND OFF TIMER 90 3 1 VIDEO(S VIDEO), COMPONENT/ RGB, PC mode 2 ASPECT mode (see page 22) 3 OFF TIMER The off timer indicator is displayed only when the off timer has been set. N button (see page 25, 26, 28, 29) VOL N R R button (see page 21) ACTION button Press to make selections POSITION buttons SET UP button (see page 20) SOUND button (see page 26) ASPECT PICTURE SOUND SET UP PICTURE button (see page 28) PICTURE POS. /SIZE PICTURE POS. /SIZE button (see page 24) PC OFF TIMER ASPECT button Press to adjust the aspect. (see page 22) PC button Press the "PC" mode selection button to select the PC mode. OFF TIMER button This button is used to switch The Plasma Display can be preset to switch to stand-by after a fixed period. setting changes to 30 minutes, 60 minutes, 90 minutes and 0 minutes (off timer cancelled) each time the button is pressed. 30 60 90 When three minutes remain, "OFF TIMER 3" will flash. The off timer is cancelled if a power interruption occurs. 0 10 Connections SPEAKER Terminals (R) SPEAKER Terminals (L) AC cord connection (see page 18) ­ Cable fixing bands Secure any excess cables with bands, as required. Pass the attached cable fixing To secure cables connected to Terminals, wrap band through the clip as the cable fixing band around them then pass the pointed end through the locking block, as shown shown in the figure. While ensuring there is sufficient slack in cables to minimize stress (especially in the power cord), firmly bind all cables with the supplied fixing band. 1 To tighten: 2 To tighten: Push the catch Pull Pull AUDIO R AUDIO L VIDEO S VIDEO R AUDIO L VD HD PR/CR/R PB/CB/B Y/G AV IN COMPONENT/RGB IN PC IN SERIAL AV IN Terminals (see page 12, 13) COMPONENT/RGB IN and Audio IN Terminals (see page 13, 14) From EXIT monitor Terminal on Computer (see page 15) From SERIAL Terminal on Computer (see page 17) 11 Connections Speakers connection When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker's Installation Manual for details on speaker installation. 1 Speakers (Optional accessories) 2 1 2 AV Input Terminals connection Connect the signal source equipment. An S VIDEO VCR connection (S VIDEO VCR) R Audio OUT L Video OUT S Video OUT S VIDEO 4 pin socket Luminance earth Chrominance earth 2×RCA audio cables AUDIO Audio input to L/R sockets S VIDEO Video input to S VIDEO socket Luminance in Chrominance in R AUDIO L VIDEO S VIDEO AV IN Note: Additional equipment and cables shown are not supplied with this set. 12 Connections 3×RCA audio video cables connection × (VCR) R Audio OUT L Video OUT AUDIO-VIDEO Video input to RCA socket 3×RCA audio video cables Audio input to L/R sockets R AUDIO L VIDEO S VIDEO AV IN Notes: (1) The S Video input will override the composite video signal when S Video lead is connected. (2) Additional equipment and cables shown are not supplied with this set. COMPONENT/RGB Input connection Component signals (Y, PB, PR ) connection (DVD Player) Y Y, PB, PR PB PR 3×RCA video cables AUDIO 2×RCA audio cables Audio input to L/R sockets R AUDIO L VD HD PR/CR/R PB/CB/B Y/G L R Notes: (1) Change the "COMPONENT/RGB-IN" setting in the "SET UP" menu to "COMPONENT". (see page 36) (2) Additional equipment and cables shown are not supplied with this set. COMPONENT/RGB IN 13 Connections RGB signal (R, G, B, HD, VD) connection RGB input to R, G, B, HD, VD sockets Example of input signal source HDTV-compatible VCR BNC-RCA adaptor plug 5×BNC RGB cables RGB camera R AUDIO L VD HD PR/CR/R PB/CB/B Y/G COMPONENT/RGB IN AUDIO 2×RCA audio cables Audio input to L/R sockets Computer VD HD R B G Notes: (1) Change the "COMPONENT/RGB-IN" setting in the "SET UP" menu to "RGB". (see page 36) (2) Additional equipment, cables and adaptor plugs shown are not supplied with this set. 14 Connections PC Input Terminals connection COMPUTER AUDIO PC IN POWER / R - STANDBY G POWER ON INPUT -- VOL + Conversion adapter (if necessary) Less than 3" 15/16 (10 cm) Ferrite core (large size) (supplied) D-sub 15p RGB PC cable Ferrite core (small size) (supplied) Less than 3" 15/16 (10 cm) Audio Stereo plug Connect a cable that matches the audio output terminal on the computer. Installing the ferrite core (Small size) 1 2 Open Press the cable through and close 3 Pull back the tabs (in two places) Installing the ferrite core (Large size) 1 2 Open Press the cable through and close 3 Pull back the tabs (in two places) Notes: (1) Computer signals which can be input are those with a horizontal scanning frequency of 15. 6 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1, 200 lines. ) (2) The display resolution is a maximum of 640 × 480 dots when the aspect mode is set to "NORMAL", and 852 × 480 dots when the aspect mode is set to "FULL". [. . . ] Press to select each item. SET UP COMPONENT/RGB-IN SELECT RGB SIGNAL SCREENSAVER ENGLISH (US) OSD LANGUAGE MULTI DISPLAY SETUP SET UP TIMER Press SIGNAL SYNC R (ACTION) button [ RGB ] H&V H-FREQ. V-FREQ. 31. 5 kHz 60. 0 Hz [ PC ] H&V Press to exit from adjust mode. SIGNAL SYNC H-FREQ. 31. 5 kHz 60. 0 Hz Setting RGB sync signal Confirm that the input is set to RGB INPUT (this setting is valid only for RGB INPUT). H & V: The H and V sync signals are input from the HD/VD connector. [. . . ]