User manual PANASONIC TH-37PX8BA

[. . . ] The exclamation point within a triangle is intended to tell the user that important operating and servicing instructions are in the papers with the appliance. WARNING: To prevent damage which may result in fire or shock hazard, do not expose this apparatus to rain or moisture. Do not place containers with water (flower vase, cups, cosmetics, etc. ) above the set. (including on shelves above, etc. ) WARNING: 1) To prevent electric shock, do not remove cover. Refer servicing to qualified service personnel. [. . . ] Have the Display evaluated at an Authorized Service Center. Services to the Display by any unauthorized personnel are strongly discouraged due to its high voltage dangerous nature. · If water or foreign objects get inside the Plasma Display, if the Plasma Display is dropped, or if the cabinet becomes damaged, disconnect the power cord plug immediately. A short may occur, which could cause fire. Contact an Authorized Service Center for any repairs that need to be made. · 6 Safety Precautions CAUTION This Plasma Display is for use only with the following optional accessories. Use with any other type of optional accessories may cause instability which could result in the possibility of injury. (All of the following accessories are manufactured by Matsushita Electric Industrial Co. , Ltd. ) · Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TY-SP37P5W-K (TH-37PW5) TY-SP42PWD3W, TY-SP42P5W-K (TH-42PW5) Pedestal (supplied for USA) . . . . . . . . . . . . TY-ST05-K · · Wall-hanging bracket (vertical) . . . . . . . TY-WK37PV3 (TH-37PW5) · Wall-hanging bracket (angled) . . . . . . . Use this cloth to wipe the cabinet, and then wipe it dry with a dry cloth. Do not allow any detergent to come into direct contact with the surface of the Plasma Display. /SIZE PICTURE POS. /SIZE button (see page 24) PC OFF TIMER ASPECT button Press to adjust the aspect. (see page 22) PC button Press the "PC" mode selection button to select the PC mode. OFF TIMER button This button is used to switch The Plasma Display can be preset to switch to stand-by after a fixed period. setting changes to 30 minutes, 60 minutes, 90 minutes and 0 minutes (off timer cancelled) each time the button is pressed. 30 60 90 When three minutes remain, "OFF TIMER 3" will flash. The off timer is cancelled if a power interruption occurs. 0 10 Connections SPEAKER Terminals (R) SPEAKER Terminals (L) AC cord connection (see page 18) ­ Cable fixing bands Secure any excess cables with bands, as required. Pass the attached cable fixing To secure cables connected to Terminals, wrap band through the clip as the cable fixing band around them then pass the pointed end through the locking block, as shown shown in the figure. While ensuring there is sufficient slack in cables to minimize stress (especially in the power cord), firmly bind all cables with the supplied fixing band. 1 To tighten: 2 To tighten: Push the catch Pull Pull AUDIO R AUDIO L VIDEO S VIDEO R AUDIO L VD HD PR/CR/R PB/CB/B Y/G AV IN COMPONENT/RGB IN PC IN SERIAL AV IN Terminals (see page 12, 13) COMPONENT/RGB IN and Audio IN Terminals (see page 13, 14) From EXIT monitor Terminal on Computer (see page 15) From SERIAL Terminal on Computer (see page 17) 11 Connections Speakers connection When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker's Installation Manual for details on speaker installation. 1 Remove the tubes from the ends of the speaker wires. Speakers (Optional accessories) 2 3 1 2 AV Input Terminals connection Connect the signal source equipment. An S VIDEO VCR connection (S VIDEO VCR) R Audio OUT L Video OUT S Video OUT S VIDEO 4 pin socket Luminance earth Chrominance earth 2×RCA audio cables AUDIO Audio input to L/R sockets S VIDEO Video input to S VIDEO socket Luminance in Chrominance in R AUDIO L VIDEO S VIDEO AV IN Note: Additional equipment and cables shown are not supplied with this set. 12 Connections 3×RCA audio video cables connection × (VCR) R Audio OUT L Video OUT AUDIO-VIDEO Video input to RCA socket 3×RCA audio video cables Audio input to L/R sockets R AUDIO L VIDEO S VIDEO AV IN Notes: (1) S-Video input will override the composite video signal when S-Video lead is connected. (2) Additional equipment and cables shown are not supplied with this set. COMPONENT/RGB Input connection Component signals (Y, PB, PR ) connection (DVD Player) Y Y, PB, PR PB PR 3×RCA video cables AUDIO 2×RCA audio cables Audio input to L/R sockets R AUDIO L VD HD PR/CR/R PB/CB/B Y/G L R COMPONENT/RGB IN Notes: (1) Change the "COMPONENT/RGB-IN" setting in the "SET UP" menu to "COMPONENT". [. . . ] ("SIGNAL [VIDEO]" menu is displayed. ) Press to select 3:2 PULLDOWN. Press to set ON/OFF. COMPONENT/RGB-IN SELECT RGB SIGNAL SCREENSAVER ENGLISH (US) OSD LANGUAGE Press SIGNAL (ACTION) button [ VIDEO ] ON AUTO OFF NORMAL [ COMPONENT ] OFF Note: When ON, this setting only affects the following signal input: · NTSC signal input during "VIDEO (S VIDEO)" input signal mode. · 525i(480i) signal input during "COMPONENT" input signal mode. R 3D Y/C FILTER (NTSC) COLOR SYSTEM 3:2 PULLDOWN Panasonic AUTO (4:3 ) SIGNAL 3:2 PULLDOWN Press to exit from adjust mode. 33 SET UP for Input Signals SYNC Select SIGNAL from the "SET UP" menu during RGB or PC input signal mode. Press to adjust. SET UP COMPONENT/RGB-IN SELECT RGB SIGNAL SCREENSAVER ENGLISH (US) OSD LANGUAGE Press SIGNAL SYNC R (ACTION) button [ RGB ] H&V Press to exit from adjust mode. SIGNAL SYNC H-FREQ. [. . . ]