User manual PANASONIC TH42PH20ER

[. . . ] Model No. TH-42PH20ER Operating Instructions High Definition Plasma Display h English Please read these instructions before operating your set and retain them for future reference. Dear Panasonic Customer Welcome to the Panasonic family of customers. We hope that you will have many years of enjoyment from your new Plasma Display. To obtain maximum benefit from your set, please read these Instructions before making any adjustments, and retain them for future reference. Retain your purchase receipt also, and note down the model number and serial number of your set in the space provided on the rear cover of these instructions. [. . . ] · The "Hue" setting can be adjusted for NTSC signal only during Video (S Video) input signal. · In Contrast, there is not a noticeable change even when contrast is increased with a bright picture or reduced with a dark picture. Advanced settings Item Black extension Input level Gamma AGC W/B High R W/B High G W/B High B W/B Low R W/B Low G W/B Low B Less Effect More Details Adjusts the dark shades of the image in gradation. Adjustment of parts which are extremely bright and hard to see. S Curve 2. 0 2. 2 2. 6 Less More Down Up Off On Increases the brightness of dark signal automatically. Adjusts the white balance for light red areas. Adjusts the white balance for light green areas. Adjusts the white balance for light blue areas. Adjusts the white balance for dark red areas. Adjusts the white balance for dark green areas. Adjusts the white balance for dark blue areas. Less More Less More Less More Less More Less More Less More Notes: · Carry out "W/B" adjustment as follows. Adjust the white balance of the bright sections using the "W/B High R", "W/B High G" and "W/B High B" settings. Adjust the white balance of the dark sections using the "W/B Low R", "W/B Low G" and "W/B Low B" settings. Steps 1 and 2 affect each other's settings, so repeat each step in turn to make the adjustment. · The adjustment values are memorized separately for each input terminal. · The adjustment range values should be used as an adjustment reference. Helpful Hint ( / Normalise Normalisation) On the remote control unit, while the "Advanced settings" menu is displayed, if either the N button is pressed at any time or the ACTION ( ) button is pressed during "Normalise", then all adjustment values are returned to the factory settings. 25 Sound Adjustment 1 2 Press to display the Sound menu. Select the desired level by listening to the sound. Sound Normalise Normal 1/2 Normal 0 0 0 Sound Mode Bass Treble Balance 3 Item Sound Mode Bass Treble Balance Press to exit from adjust mode. Details Normal: Emits the original sound. Adjusts left and right volumes. Note: Bass and Treble settings are memorized separately for each Sound Mode. Helpful Hint ( / Normalise Normalisation) While the "Sound" menu is displayed, if either the N button on the remote control is pressed at any time or the ACTION ( ) button is pressed during "Normalise", then all adjustment values are returned to the factory settings. SDI Sound Output This menu is displayed when HD-SDI Terminal Board with audio (TY-FB10HD) is installed to the unit. SDI Sound Output Left Channel Right Channel Sound Out Level Meter 2/2 Channel 1 Channel 1 Off Off Item Left Channel Right Channel Sound Out Details Channel 1 to Channel 16 Selects left audio channel. Channel 1 to Channel 16 Selects right audio channel. Disables audio output. Note: This menu is available only when selecting a slot that HD-SDI Terminal Board with audio (TY-FB10HD) is installed. Level Meter Off 1-8ch 9-16ch Sets audio channels to show in the audio level meter. 8 channels are displayed in the audio level meter; 4 channels each on both right and left sides of the display. 1-8ch: Displays the audio level meter (1-8ch) 9-16ch: Displays the audio level meter (9-16ch) 26 PRESENT TIME Setup / Set up TIMER The timer can switch the Plasma Display On or Off. [. . . ] 5: When selected the RGB format and 525p signal input to the PC IN terminal, it is recognized as VGA 60Hz signal. 6: When inputted VGA 60Hz format signal from the other than PC IN terminal, it is recognized as 525p signal. Note: Signals without above specification may not be displayed properly. 51 Applicable Input Signals Video input (VIDEO) Signal name 1 2 3 4 5 NTSC PAL PAL60 SECAM Modified NTSC Horizontal frequency(kHz) 15. 73 15. 63 15. 73 15. 63 15. 73 Vertical frequency(Hz) 59. 94 50. 00 59. 94 50. 00 59. 94 Shipping condition This function allows you to reset the unit to the factory setting. 1 2 3 Setup 1/2 Press to display the Setup menu. Press to select "OSD Language". Signal Screensaver Extended life settings Input label Component/RGB-in select Power save Standby save PC Power management DVI-D Power management Auto power off OSD Language RGB Off Off Off Off Off English (UK) Press for more than 3 seconds. Press to select "Shipping". Press to display the Shipping menu. Options Shipping 4 Press to select "YES". Shipping YES NO Press to confirm. [. . . ]