User manual PANASONIC TH-42PHW5UZ

[. . . ] ® PLASMA DISPLAY High Definition Plasma Display Operating Instructions + -- INPUT VOL POWE R / BY R - STAND ON G POWER Model No. TH-42PHW5 TH-50PHW5 For assistance, please call : 1-888-VIEW-PTV(843-9788) or send e-mail to : consumerproducts@panasonic. com or visit us at www. panasonic. com (U. S. A) (Puerto Rico) (Canada) For assistance, please call : 787-750-4300 or visit us at www. panasonic. com For assistance, please call : 1-800-561-5505 or visit us at www. panasonic. ca Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference. English TQBC0453-1 WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: To reduce the risk of electric shock, do not remove cover or back. Refer servicing to qualified service personnel. The lightning flash with arrow-head within a triangle is intended to tell the user that parts inside the product are a risk of electric shock to persons. [. . . ] If water droplets get inside the unit, operating problems may result. Avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the cabinet surface may be adversely affected or the coating may peel off. Furthermore, do not leave it for long periods in contact with articles made from rubber or PVC. Note: Do not allow a still picture to be displayed for an extended period, as this can cause a permanent after-image to remain on the Plasma Display. Examples of still pictures include logos, video games, computer images, teletext and images displayed in 4:3 mode. 7 Accessories Accessories Supplied Check that you have the Accessories and items shown Operating Instruction book Remote Control Transmitter EUR646525 INPUT SURROUND VOL Batteries for the Remote Control Transmitter (AA(R6) Battery × 2) AC cord N R PICTURE SOUND SET UP PICTURE POS. /SIZE ASPECT PC OFF TIMER PLASMA DISPLAY Warranty Ferrite core (small size) J0KF00000018 × 1 Ferrite core (large size) J0KG00000054 × 2 Fixing bands TMME187 × 2 Speaker Wire × 2 Optional Accessories · Speakers TY-SP42P5W-M (TH-42PHW5) TY-SP50P5W-M (TH-50PHW5) · Pedestal · Wall stand TY-ST10-M TY-ST42PW1 · Wall-hanging bracket (angled) TY-WK42PR1 For assembling Full instructions are supplied with each of the optional accessories for use with this Plasma Display. 8 Remote Control Batteries Requires two AA batteries. Install the batteries as shown in the battery compartment. (Polarity + or ­ must match the markings in the compartment. ) 3. Replace the cover and slide in reverse until the lock snaps. Two "AA" size Helpful Hint: For frequent remote control users, replace old batteries with Alkaline batteries for longer life. Precaution on battery use Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter. Batteries should always be replaced as a pair. Always use new batteries when replacing the old set. Do not combine a used battery with a new one. Do not mix battery types (example: "Zinc Carbon" with "Alkaline"). Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries. Battery replacement is necessary when the remote control acts sporadically or stops operating the Plasma Display. 9 Basic Controls R - STANDBY G POWER ON TH-50PHW5 INPUT -- VOL + Main POWER ON/OFF Switch Power Indicator The Power Indicator will light. POWER-OFF Indicator not illuminated (The unit will still consume some power as long as the power cord is inserted into the wall outlet. ) STAND-BY . . . . . Red POWER-ON. . . . . Green · · · INPUT button (VIDEO(S VIDEO), COMPONENT/RGB, PC Mode Selection) Press the "INPUT" button to select VIDEO (S VIDEO), COMPONENT/RGB, PC input signal modes sequentially. (see page 19) VOLUME Adjustment Press the Volume Up "+" or Down "­" button to increase or decrease the sound volume level. STAND-BY(ON/OFF) button The Plasma Display must first be plugged into the wall outlet and turned on at the power switch (see page 18). Press this button to turn the Plasma Display ON, from STANDBY mode. Press it again to turn the High Definition Plasma Display OFF to STAND-BY mode. STATUS button Press the "STATUS" button to display the current system status. VIDEO NORMAL SURROUND button (see page 27) INPUT button (VIDEO(S VIDEO), COMPONENT/ RGB, PC Mode Selection) Press to select VIDEO(S VIDEO), COMPONENT/RGB, PC input signal modes sequentially. (see page 19) INPUT 1 2 Sound mute On/Off (see page 26) VOLUME Adjustment Press the Volume Up "+" or Down "­" button to increase or decrease the sound volume level. SURROUND OFF TIMER 90 3 VOL 1 VIDEO(S VIDEO), COMPONENT/RGB, PC mode 2 ASPECT mode (see page 22) 3 OFF TIMER The off timer indicator is displayed only when the off timer has been set. N button (see page 25, 26, 28) N R R button (see page 21) ACTION button Press to make selections POSITION buttons SET UP button (see page 20) SOUND button (see page 26) ASPECT PICTURE SOUND SET UP PICTURE button (see page 28) PICTURE POS. [. . . ] V-FREQ. 31. 5 kHz 60. 0 Hz Setting RGB sync signal Confirm that the input is set to RGB INPUT (this setting is valid only for RGB INPUT). H & V: The H and V sync signals are input from the HD/VD connector. ON G: Uses a synchronized signal on the Video G signal, which is input from the G connector. ON VIDEO: The composite video signal input from the VIDEO input terminal is used by dividing the sync signals. SYNC H&V SYNC ON G SYNC ON VIDEO Setting PC sync signal Confirm that the input is set to PC INPUT (this setting is valid only for PC INPUT). [. . . ]