User manual PANASONIC TH-42PW3U

[. . . ] ® Wide Plasma Display PLASMA DISPLAY Operating Instructions Model No. + -- INPUT VOL R POWE / BY R - STAND ON G POWER TH-42PW3 R - STANDBY G POWER ON INPUT -- VOL + For assistance, please call : 1-888-VIEW-PTV(843-9788) or send e-mail to : consumerproducts@panasonic. com or visit us at www. panasonic. co. jp/global/ (U. S. A) (Puerto Rico) (Canada) For assistance, please call : 787-750-4300 For assistance, please call : 1-800-561-5505 or visit us at www. panasonic. co. jp/global/ Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference. English TQBC0218-1 WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: To reduce the risk of electric shock do not remove cover or back. Refer servicing to qualified service personnel. The lightning flash with arrow-head within a triangle is intended to tell the user that parts inside the product are a risk of electric shock to persons. [. . . ] Use this cloth to wipe the cabinet, and then wipe it dry with a dry cloth. Do not allow any detergent to come into direct contact with the surface of the Wide Plasma Display. If water droplets get inside the unit, operating problems may result. Avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the cabinet surface may be adversely affected or the coating may peel off. Furthermore, do not leave it for long periods in contact with articles made from rubber or PVC. Note: Do not allow a still picture to be displayed for an extended period, as this can cause a permanent after-image to remain on the Wide Plasma Display. Examples of still pictures include logos, video games, computer images, teletext and images displayed in 4:3 mode. 8 Accessories Accessories Supplied Check that you have the Accessories and items shown Operating Instruction book Remote Control Transmitter EUR646525 INPUT SURROUND Batteries for the Remote Control Transmitter (AA(R6) Battery × 2) VOL N R PICTURE SOUND SET UP PICTURE POS. /SIZE ASPECT PC OFF TIMER PLASMA DISPLAY Warranty RCA/BNC Adapter Plug Ferrite core × 2 KRCBC160928B Optional Accessories · Speakers TY-SP42PWD3W · Pedestal TY-ST42PT3-K · Wall stand TY-ST42PW1 · Wall-hanging bracket (angled) TY-WK42PR1 · Connecting Cable TY-SCP15C03 49. 2 ft (15 m) 9 Remote Control Batteries Requires two AA batteries. Install the batteries as shown in the battery compartment. (Polarity + or ­ must match the markings in the compartment). Replace the cove and slide in reverse until the lock snaps. Two "AA" size Helpful Hint: For frequent remote control users, replace old batteries with Alkaline batteries for longer life. Precaution on battery use Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter. Batteries should always be replaced as a pair. Always use new batteries when replacing the old set. Do not combine a used battery with a new one. Do not mix battery types (example: "Zinc Carbon" with "Alkaline"). Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries. Battery replacement is necessary when the remote control acts sporadically or stops operating the Plasma Display. 10 Basic Controls R - STANDBY G POWER ON TH-42PW3 INPUT -- VOL + Main Power On/Off Switch Power Indicator The Power Indicator will light. Indicator not illuminated (The unit will still consume some power as long as the power cord is still inserted into the wall outlet. ) Stand-by . . . . Green · · · Input button (VIDEO (S-VIDEO)/COMPONENT, RGB/PC Mode Selection) Push the "INPUT" button to select VIDEO(S-VIDEO)/COMPONENT or RGB/PC input signal modes sequentially. Volume Adjustment Push the Volume Up "+" or Down "­" button to increase or decrease the sound volume level. Stand-by (ON/OFF) button The Wide Plasma Display must first be plugged into the wall outlet and turn on at the power switch (see page 18). Push this button to turn the Wide Plasma Display ON, from STANDBY mode. Push it again to turn the Wide Plasma Display OFF to STANDBY mode. Status button Push the "Status" button to display the current system status. VIDEO NORMAL SURROUND button (see page 27) Input button (VIDEO(S-VIDEO)/COMPONENT, RGB/PC Mode Selection) Press to select VIDEO(S-VIDEO)/ COMPONENT or RGB/PC input signal modes sequentially. [. . . ] 60. 0 Hz SIGNAL [ PC ] The following operation methods are the same for both the SIGNAL [RGB] and SIGNAL [PC]. H&V SYNC NARROW PULL-IN RANGE CLAMP POSITION H-FREQ. 60. 0 Hz SYNC Setting RGB sync signal setting: Confirm that the input is set to RGB INPUT (this setting is valid only for RGB INPUT). H&V: The H and V sync signals are input from the HD/VD (BNC) connector. ON G: Uses a synchronized signal on the Video G signal, which is input from the G (BNC) connector. [. . . ]