User manual PANASONIC TH-42PW5LZ

[. . . ] ® PLASMA DISPLAY Progressive Wide Plasma Display Operating Instructions + -- INPUT VOL POWE R / BY R - STAND ON G POWER Model No. TH-37PW5 TH-42PW5 Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference. English TQBC0520 WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: To reduce the risk of electric shock, do not remove cover or back. Refer servicing to qualified service personnel. The lightning flash with arrow-head within a triangle is intended to tell the user that parts inside the product are a risk of electric shock to persons. [. . . ] Install the batteries as shown in the battery compartment. (Polarity + or ­ must match the markings in the compartment. ) 3. Replace the cover and slide in reverse until the lock snaps. Two "AA" size Helpful Hint: For frequent remote control users, replace old batteries with Alkaline batteries for longer life. Precaution on battery use Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter. Batteries should always be replaced as a pair. Always use new batteries when replacing the old set. Do not combine a used battery with a new one. Do not mix battery types (example: "Zinc Carbon" with "Alkaline"). Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries. Battery replacement is necessary when the remote control acts sporadically or stops operating the Plasma Display. 8 Basic Controls Main POWER ON/OFF Switch R - STANDBY G POWER ON INPUT -- VOL + TH-42PW5 · · · Remote control sensor Power Indicator The Power Indicator will light. POWER-OFF Indicator not illuminated (The unit will still consume some power as long as the power cord is inserted into the wall outlet. ) STAND-BY . . . . . Red POWER-ON. . . . . Green INPUT button (VIDEO (S VIDEO), COMPONENT/RGB and PC Mode Selection) (see page 18) VOLUME Adjustment Press the Volume Up "+" or Down "­" button to increase or decrease the sound volume level. STAND-BY(ON/OFF) button The Plasma Display must first be plugged into the wall outlet and turned on at the power switch. (see page 17) Press this button to turn the Plasma Display ON, from STAND-BY mode. Press it again to turn the Plasma Display OFF to STAND-BY mode. STATUS button Press the "STATUS" button to display the current system status. VIDEO NORMAL C. A. T. S sensor Plasma C. A. T. S (Contrast Automatic Tracking System) Plasma C. A. T. S automatically senses the ambient light conditions and adjusts the brightness and gradation accordingly, to optimise contrast. (Effective when Picture mode is set to Auto. ) SURROUND button (see page 27) INPUT button (VIDEO(S VIDEO), COMPONENT/ RGB, PC Mode Selection) Press to select VIDEO(S VIDEO), COMPONENT/RGB, PC input signal modes sequentially. (see page 18) INPUT 1 2 Sound mute On/Off (see page 26) VOLUME Adjustment Press the Volume Up "+" or Down "­ " button to increase or decrease the sound volume level. SURROUND OFF TIMER 90 3 1 VIDEO(S VIDEO), COMPONENT/ RGB, PC mode 2 ASPECT mode (see page 22) 3 OFF TIMER The off timer indicator is displayed only when the off timer has been set. N button (see page 25, 26, 28) VOL N R R button (see page 21) ACTION button Press to make selections POSITION buttons SET UP button (see page 20) SOUND button (see page 26) ASPECT PICTURE SOUND SET UP PICTURE button (see page 28) PICTURE POS. /SIZE PICTURE POS. /SIZE button (see page 24) PC OFF TIMER ASPECT button Press to adjust the aspect. (see page 22) PC button Press the "PC" mode selection button to select the PC mode. OFF TIMER button This button is used to switch The Plasma Display can be preset to switch to stand-by after a fixed period. setting changes to 30 minutes, 60 minutes, 90 minutes and 0 minutes (off timer cancelled) each time the button is pressed. 30 60 90 When three minutes remain, "OFF TIMER 3" will flash. The off timer is cancelled if a power interruption occurs. [. . . ] · 525i(480i) signal input during "COMPONENT" input signal mode. R 3D Y/C FILTER (NTSC) COLOR SYSTEM 3:2 PULLDOWN Panasonic AUTO (4:3 ) SIGNAL 3:2 PULLDOWN Press to exit from adjust mode. 33 SET UP for Input Signals SYNC Select SIGNAL from the "SET UP" menu during RGB or PC input signal mode. Press to adjust. SET UP COMPONENT/RGB-IN SELECT RGB SIGNAL SCREENSAVER ENGLISH (US) OSD LANGUAGE Press SIGNAL SYNC R (ACTION) button [ RGB ] H&V Press to exit from adjust mode. SIGNAL SYNC H-FREQ. V-FREQ. 31. 5 kHz 60. 0 Hz [ PC ] H&V H-FREQ. V-FREQ. 31. 5 kHz 60. 0 Hz Setting RGB sync signal Confirm that the input is set to RGB INPUT (this setting is valid only for RGB INPUT). [. . . ]