User manual PANASONIC TH-42PW6LZ

[. . . ] ® Operating Instructions PLASMA DISPLAY Progressive Wide Plasma Display VOL -- MENU INPUT + ENTER POWE R / BY R - STAND ON G POWER Model No. TH-42PW6 Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference. English TQBC0596 2 WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: To reduce the risk of electric shock, do not remove cover or back. Refer servicing to qualified service personnel. The lightning flash with arrow-head within a triangle is intended to tell the user that parts inside the product are a risk of electric shock to persons. [. . . ] COMPUTER 1 6 2 7 3 8 4 9 5 Ferrite core RS-232C (large size) Straight cable (supplied) SERIAL Pin layout for RS-232C Installing the ferrite core (Large size) D-sub 9p Less than 3" 15/16 (10 cm) Open Notes: (1) Use the RS-232C cable to connect the computer to the Plasma Display. (2) The computer shown is for example purposes only. (3) Additional equipment and cables shown are not supplied with this set. The SERIAL terminal conforms to the RS-232C interface specification, so that the Plasma Display can be controlled by a computer which is connected to this terminal. The computer will require software which allows the sending and receiving of control data which satisfies the conditions given below. Use a computer application such as programming language software. Refer to the documentation for the computer application for details. Communication parameters Signal level Synchronization method Baud rate Parity Character length Stop bit Flow control RS-232C compliant Asynchronous 9600 bps None 8 bits 1 bit ­ RS-232C Conversion cable Details D-sub 9-pin female RXD 2 3 TXD 5 GND Non use 4·6 7 8 1·9 Shorted NC Basic format for control data The transmission of control data from the computer starts with a STX signal, followed by the command, the parameters, and lastly an ETX signal in that order. If there are no parameters, then the parameter signal does not need to be sent. STX C1 C2 C3 : P1 P2 P3 P4 P5 ETX End (03h) Command Command PON POF AVL AMT IMS Parameter None None Control details Power ON Power OFF Volume 00 - 63 Audio MUTE OFF Audio MUTE ON Input select (toggle) Slot1 input Slot2 input Slot3 input PC input Screen mode select (toggle) NORMAL (4:3) ZOOM FULL JUST Panasonic AUTO ** Start (02h) Colon Parameter(s) (1 - 5 bytes) 3-character command (3 bytes) DAM Notes: (1) If multiple commands are transmitted, be sure to wait for the response for the first command to come from this unit before sending the next command. (2) If an incorrect command is sent by mistake, this unit will send an "ER401" command back to the computer. With the power off, this display responds to PON command only. 0 1 None SL1 SL2 SL3 PC1 None NORM ZOOM FULL JUST SELF 11 Connections Connection Back view of the Plasma Display R AUDIO L VIDEO R AUDIO L PR/CR/R PB/CB/B Y/G AV IN SLOT1 S VIDEO SLOT 1 2 3 COMPONENT/RGB IN SLOT3 SLOT 1 2 3 SLOT2 PC VCR R AUDIO OUT L CAMCORDER VIDEO OUT S VIDEO OUT R L PR PB Y AUDIO OUT DVD(Y, PB, PR)OUT S VIDEO 4 pin socket Luminance earth Chrominance earth DVD PLAYER Luminance in Chrominance in Digital TV Set-Top-Box (DTV-STB) Applicable input signals [ Example ] Signal name 1 2 3 4 5 NTSC PAL PAL60 SECAM Modified NTSC Horizontal Vertical frequency(kHz) frequency(Hz) 15. 73 15. 63 15. 73 15. 63 15. 73 59. 94 50. 00 59. 94 50. 00 59. 97 1 2 3 4 5 6 7 8 9 10 11 Applicable input signals [ Example ] Signal name 525 (480) / 60i 525 (480) / 60p 625 (575) / 50i 625 (575) / 50p 750 (720) / 60p 750 (720) / 50p 1, 125 (1, 080) / 60i 1, 125 (1, 080) / 50i 1, 125 (1, 080) / 24p 1, 125 (1, 080) / 24sF 1, 250 (1, 080) / 50i Horizontal Vertical frequency(kHz) frequency(Hz) 15. 73 31. 47 15. 63 31. 25 45. 00 37. 50 33. 75 28. 13 27. 00 27. 00 31. 25 59. 94 59. 94 50. 00 50. 00 60. 00 50. 00 59. 94 50. 00 24. 00 48. 00 50. 00 Notes: (1) The S Video input will override the composite video signal when S Video lead is connected. (2) Additional equipment and cables shown are not supplied with this set. 12 Power ON/OFF AC cord connection Connecting the AC cord plug to the Plasma Display. Fix the AC cord plug securely to the Plasma Display with the clamper. Power ON/OFF Connecting the plug to the Wall Outlet Press the POWER switch on the Plasma Display to turn the set on : POWER-ON. Power Indicator : Green R - STANDBY G POWER ON INPUT MENU --VOL + ENTER R - STANDBY G POWER ON TH-42PW6 Example: The screen below is displayed for a while after the Plasma Display is turned on. (setting condition is an example. ) Remote Control Sensor From the second time on, the screen shown below is displayed for a while (setting condition is an example). PC NORMAL Power Indicator When the POWER is turned on for the first time, the LANGUAGE selection screen is displayed. From the second time on, language selection can be done from the setup menu. (see page 18) Select the desired language using the and keys and press the ACTION button. OSD LANGUAGE English (UK) Deutsch Fran ais Italiano Espa ol ENGLISH (US) SELECT SET Press the button on the remote control to turn the Plasma Display off. Power Indicator: Red (STAND-BY) INPUT SURROUND Press the button on the remote control to turn the Plasma Display on. Power Indicator: Green To turn the power for the Plasma Display off, press the switch on the Plasma Display, when the Plasma Display is on or in standby mode. Note: During operation of the power management function, the power indicator turns orange in the power off state. VOL N R 13 Basic Controls Main Power On/Off Switch R - STANDBY G POWER ON INPUT MENU ­ VOL + ENTER TH-42PW6 Enter/Aspect button (see page 16, 19) Remote control MENU Screen ON/OFF Power Indicator sensor Each time the MENU button is pressed, the menu The Power Indicator will light. Indicator not illuminated (The unit will still consume some power as long as the power cord Normal Viewing PICTURE SET UP is still inserted into the wall outlet. ) SOUND PICTURE POS. / SIZE Stand-by . . . . Green (INPUT1, INPUT2, INPUT3 and PC IN Selection) DPMS . . . . . . . . . . . . [. . . ] Press to set ON/OFF. COMPONENT/RGB-IN SELECT INPUT LABEL RGB RGB1 SIGNAL SCREENSAVER OFF POWER SAVE ON STANDBY SAVE OFF POWER MANAGEMENT ENGLISH (US) OSD LANGUAGE Press SIGNAL R (ACTION) button [ VIDEO ] ON AUTO OFF NORMAL [ COMPONENT ] OFF Press to exit from adjust mode. Note: When ON, this setting only affects the following signal input: · NTSC / PAL signal input during "VIDEO (S VIDEO)" input signal. · 525i(480i) signal input during "COMPONENT" input signal. 3D Y/C FILTER (NTSC) COLOR SYSTEM 3:2 PULLDOWN Panasonic AUTO (4:3 ) SIGNAL 3:2 PULLDOWN 30 SET UP for Input Signals SYNC Select SIGNAL from the "SET UP" menu during RGB input signal. Press to select each item. SET UP COMPONENT/RGB-IN SELECT INPUT LABEL RGB RGB1 1/2 SIGNAL SCREENSAVER OFF POWER SAVE ON STANDBY SAVE OFF POWER MANAGEMENT ENGLISH (US) OSD LANGUAGE Press SIGNAL R (ACTION) button [ RGB ] H&V Press to exit from adjust mode. SYNC H-FREQ. [. . . ]