User manual PANASONIC TH-42PWD6UX

[. . . ] ® Operating Instructions PLASMA DISPLAY Progressive Wide Plasma Display ­ MENU INPUT VOL + ENTER POWE R / Y R - STANDB ON G POWER Model No. TH-37PWD6UX TH-42PWD6UX Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference. English TQBC0650 WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: To reduce the risk of electric shock, do not remove cover or back. Refer servicing to qualified service personnel. The lightning flash with arrow-head within a triangle is intended to tell the user that parts inside the product are a risk of electric shock to persons. [. . . ] Power Indicator: Green To turn the power for the Plasma Display off, press the switch on the Plasma Display, when the Plasma Display is on or in standby mode. Note: During operation of the power management function, the power indicator turns orange in the power off state. VOL N R 12 Input Signal Selection Select the Input Signal INPUT Press the INPUT button to select the input signal to be played back from the equipment which has been connected to the Plasma Display. Select the input signals to be connected by installing the optional Terminal Boards. Input signals will change as follows: R - STANDBY G POWER ON INPUT MENU ­ VOL + ENTER INPUT1 INPUT MENU INPUT2 INPUT3 PC IN ­ VOL + ENTER INPUT SURROUND Notes: (1) Input terminal will not be selected if the terminal board is not installed into the SLOT. (2) Select to match the signals from the source connected to the component/RGB input terminals. (see page 32) (3) In 2 screen display, the same input mode cannot be selected for the main picture and sub picture. VOL N R Selecting the On-Screen Menu Language SET UP press to display the SET UP menu. INPUT press to select OSD LANGUAGE. press to select your preferred language. SURROUND VOL N R SET UP COMPONENT/RGB-IN SELECT RGB RGB1 1/2 Selectable languages INPUT LABEL PICTURE SOUND SET UP MULTI ZOOM ENGLISH(UK) Deutsch Français Italiano Español ENGLISH(US) . . . . . . . (Chinese) SIGNAL SCREENSAVER OFF POWER SAVE ON STANDBY SAVE OFF POWER MANAGEMENT ENGLISH (US) OSD LANGUAGE 13 Basic Controls Main Power On/Off Switch R - STANDBY G POWER ON INPUT MENU ­ VOL + ENTER Enter/Aspect button (see page 16, 18) Remote control MENU Screen ON/OFF Power Indicator sensor Each time the MENU button is pressed, the menu The Power Indicator will light. Indicator not illuminated (The unit will still consume some power as long as the power cord Normal Viewing PICTURE SET UP is still inserted into the wall outlet. ) SOUND PICTURE POS. / SIZE Stand-by . . . . Green (INPUT1, INPUT2, INPUT3 and PC IN Selection) DPMS . . . . . . . . . . . . Orange [With PC input signal and (see page 13) during operation of PC's screensaver. ] Volume Adjustment Volume Up "+" Down "­" C. A. T. S sensor When the menu screen is displayed. Plasma C. A. T. S (Contrast Automatic Tracking System) "+": press to move the cursor up Plasma C. A. T. S automatically senses the ambient light conditions and "­": press to move the cursor down adjusts the brightness and gradation accordingly, to optimise contrast. (Effective when Picture mode is set to Auto. ) (see page 16) Status button Press the "Status" button to display the current system status. 1 PC 1 Input label NORMAL 2 2 Aspect mode (see page 18) N button (see page 19, 20, 21, 22) 3 Off timer The off timer indicator is displayed only when the off timer has been set. OFF TIMER 90 3 PICTURE button (see page 21) · · · · MULTI PIP MULTI PIP Each time pressing this button main picture and sub picture will be displayed as follows bellow. [Picture and Picture] Main picture Sub picture [Picture out Picture] Main picture Sub picture MULTI PIP MULTI PIP [Picture in Picture] Main picture Sub picture Normal Viewing MULTI PIP A B SWAP A SWAP B A B SWAP SWAP Press to swap main picture and sub picture. B A [Example] B A B SELECT A Main picture label is bright PC1 VIDEO1 Sub picture label is bright PC1 VIDEO1 SELECT Press the SELECT button Under main Picture and sub picture display, select the picture which you would like to change input modes. INPUT A B A B INPUT SURROUND VOL Input modes switching is possible Main picture label is changed Sub picture label is changed Press to change input signal. R VIDEO2 VIDEO1 N C ZOOM MOVE Press the MOVE button Each time the location of the sub picture will be moved. B A PC1 VIDEO3 D Picture is changed Notes: (1) This button is effective only in the picture in picture. (2) The sub picture may be hidden by the on screen display, depending on its position. Note: Sound output is from the main picture. 14 Basic Controls Stand-by (ON/OFF) button The Plasma Display must first be plugged into the wall outlet and turned on at the power switch (see page 12). Press this button to turn the Plasma Display On, from Standby mode. Press it again to turn the Plasma Display Off to Standby mode. SURROUND button The benefits of surround sound are enormous. You can be completely enveloped in sound; just as if you were at a concert hall or cinema. ON OFF The surround setting switches on and off each time the SURROUND ON SURROUND button is pressed. Note: The surround settings are memorized separately for each Sound mode (Normal, Auto). INPUT button (INPUT1, INPUT2, INPUT3 and PC IN Selection) Press to select INPUT1, INPUT2, INPUT3 and PC IN input SLOTS sequentially. (see page 13) Sound mute On/Off (see page 20) INPUT SURROUND Volume Adjustment Press the Volume Up "+" or Down "­" button to increase or decrease the sound volume level. VOL N R R button (see page 19, 20) Press the R button to return to previous menu screen. POSITION buttons SOUND button (see page 20) Press to adjust the SOUND. [. . . ] Parts : New or rebuilt parts in exchange for defective parts for a period of 12 months. On-site service requires that the servicer be given clear, complete and easy access to the product. Providing this access is the responsibility of the purchaser. On-site service does not include removal or re-installation of an installed product. [. . . ]