User manual PANASONIC TH-46PZ85EA

[. . . ] Operating Instructions Plasma Television Model No. TH-42PZ85EA TH-46PZ85EA Contents Be Sure to Read · · · Start Guide Quick · · · · · Safety Precautions ··································· 4 (Warning / Caution) Notes ························································ 5 Maintenance ············································ 5 Accessories / Options ············· 6 Identifying Controls ·················· 9 Basic Connection ··················· 10 Auto Setup ······························· 12 How to Use Menu Functions ··· 14 Please read these instructions before operating your set and retain them for future reference. The images shown in this manual are for illustrative purposes only. Please refer to Pan European Guarantee Card if you need to contact your local Panasonic dealer for assistance. For more detailed instructions, refer to the Operating Instructions on the CD-ROM. To view the Operating Instructions on the CD-ROM, you need a computer equipped with a CD-ROM drive, and Adobe® Reader® (Version 7. 0 or later is recommended) installed on your computer. Depending on the operating system or settings on your computer, the Operating Instructions may not start automatically. [. . . ] Batteries must not be exposed to excessive heat such as sunshine, fire or the like. Attaching the pedestal Warning Do not disassemble or modify the pedestal. Otherwise the TV may fall over and become damaged, and personal injury may result. · · · · · · Caution Do not use any other TV and displays. Otherwise the TV may fall over and become damaged, and personal injury may result. Do not use the pedestal if it becomes warped or physically damaged. If you use the pedestal while it is physically damaged, personal injury may result. Contact your nearest Panasonic dealer immediately. During set-up, make sure that all screws are securely tightened. If insufficient care is taken to ensure screws are properly tightened during assembly, the pedestal will not be strong enough to support the TV, and it might fall over and become damaged, and personal injury may result. If the TV is knocked or children climb onto the pedestal with the TV installed, the TV may fall over and personal injury may result. Two or more people are required to install and remove the TV. If two or more people are not present, the TV may be dropped, and personal injury may result. Assembly screw (4) (silver) · Assembly screw (4) (black) Pole (2) XYN5+F18FN · THEL060N · · L R : TBLA3614 L : TBLA3615 R · · A Base TBLX0043 -1 (TH-42PZ85EA) TBLX0045 (TH-46PZ85EA) M5 × 18 M5 × 25 Assembling the pedestal · · · · Use the four assembly screws to fasten the left and right poles to the base securely. Make sure that the screws are securely tightened. Forcing the assembly screws the wrong way will strip the threads. "L" or "R" mark is stamped on the bottom of the pole. R Accessories / Options D L Front Securing the TV · · Use the assembly screws to fasten securely. Make sure that the screws are securely tightened. Carry out the work on a horizontal and level surface. B View from the bottom Arrow mark Hole for pedestal installation D 7 Accessories / Options Using the clamper Rear of the TV · · · Do not bundle the RF cable and mains lead together (could cause distorted image). When using the optional accessory, follow the option's assembly manual to fix cables. Attach the clamper hole To remove from the TV: snaps Bundle the cables To loosen: Insert the clamper in a hole Keep pushing both side snaps hooks Set the tip in the hooks knob Keep pushing the knob · · Adjust the panel to your desired angle Ensure that the pedestal does not hang over the edge of the base even if the TV swivels to the full rotation range. Please ensure that the unit is disconnected from the mains socket before attaching or disconnecting any leads. When disconnecting the mains lead, be absolutely sure to disconnect the mains plug at the socket outlet first. Example 1 Connecting aerial TV only Rear of the TV Aerial Example 2 Connecting DVD Recorder / VCR TV, DVD Recorder or VCR Rear of the TV Aerial AC 220-240 V 50 / 60 Hz AC 220-240 V 50 / 60 Hz Mains lead (supplied) Mains lead (supplied) RF cable AV1 RGB VIDEO AV2 RGB VIDEO S VIDEO PC AV1 RGB VIDEO AV2 RGB VIDEO S VIDEO PC COMPONENT AUDIO AUDIO IN OUT Y COMPONENT AUDIO AUDIO IN OUT Y L L PB L L PB HDMI 1 R R PR HDMI 2 R R PR HDMI 1 DIGITAL AUDIO OUT HDMI 2 DIGITAL AUDIO OUT RF cable SCART cable (fully wired) RF OUT DVD Recorder or VCR RF IN RF cable 10 · · · Note Connect to AV1 / AV2 for a DVD Recorder / VCR supporting Q-Link. For HDMI-compatible equipment, possible to connect to HDMI terminals (HDMI1 / HDMI2 / HDMI3) by using HDMI cable. Read the manual of the equipment too. Example 3 Connecting DVD Recorder / VCR and Set top box TV, DVD Recorder / VCR and Set top box Rear of the TV Aerial Push until both side tabs click Make sure that the mains lead is securely fixed. AC 220-240 V 50 / 60 Hz · To remove from the TV: Press both tabs and pull on mains connector to release tabs · Mains lead (supplied) Basic Connection RF cable AV1 RGB VIDEO AV2 RGB VIDEO S VIDEO PC COMPONENT AUDIO AUDIO IN OUT Y L L PB HDMI 1 R R PR HDMI 2 DIGITAL AUDIO OUT SCART cable (fully wired) RF OUT DVD Recorder or VCR RF IN RF cable Fully wired HDMI compliant cable SCART cable (fully wired) RF OUT RF cable RF IN Set top box RF cable RF IN 11 Auto Setup Search and store TV programmes automatically. These steps are not necessary if the setup has been completed by your local dealer. 1 2 INPUT OPTION SD CARD EXIT Plug the TV into mains socket and switch On (Takes a few seconds to be displayed) · Select the language Menüsprache Deutsch English Français Italiano Español Português Nederlands Dansk Svenska Norsk Suomi Türkçe Polski cestina Magyar Slovencina Român Srpski Hrvatski Slovenscina Latviesu eesti keel Lietuvi You can now use the remote control to turn On the TV or turn the TV to standby mode. [. . . ] Apart from stereo (2ch) audio, these signals can also be multi-channel audio. MPEG:An audio compression method that compresses audio to small size without any considerable loss of audio quality. DVB mode only Selects the initial setting for digital audio output signal from DIGITAL AUDIO OUT terminal (Auto / PCM) Auto: Dolby Digital is output as Dolby Digital Bitstream. DVB mode only How to Use Menu Functions · · Sound Audio Preference SPDIF Selection · · · · · · MPEG Optical Level Normally, MPEG sound is larger than Dolby Digital one You can adjust the audio level of MPEG output from DIGITAL AUDIO OUT terminal as the initial setting 0dB to -12dB in -2dB reductions DVB mode only Select to fit the input signal (Auto / Digital / Analogue) Auto : Automatic detection of digital or analogue sound source Digital : HDMI cable connection Analogue : HDMI-DVI adapter cable connection HDMI input mode only HDMI2 terminal is for digital signal only No setting for HDMI2 available Press the OK button to reset the present Sound Mode to the default settings HDMI1 / 3 Input Reset to Default A different menu will be displayed while PC or SD Card is used. [. . . ]