User manual PANASONIC TH-50PD12U

[. . . ] Operating Instructions Manual de instrucciones High Definition Plasma Display Alta definición Pantalla de plasma Model No. Número de modelo TH-42PD12U TH-50PD12U Contents Important Safety Instructions ··········································· 3 FCC STATEMENT ······························································· 4 Safety Precautions ···························································· 5 Maintenance ······································································· 6 Accessories ······································································· 7 Connections ······································································· 8 Power ON / OFF ······························································· 12 Selecting the input signal ··············································· Basic Controls ································································· On-Screen Menu Displays ·············································· Specifications ·································································· Panasonic Professional Flat Panel Display Limited Warranty ·· LIMITED WARRANTY STATEMENT ································ Customer Service ···························································· 14 15 17 18 19 20 21 The illustration shown is an image. Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference. [. . . ] Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries. Battery replacement is necessary when the remote control acts sporadically or stops operating the Plasma Display. Batteries must not be exposed to excessive heat such as sunshine, fire or the like. 7 Connections When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker's Installation Manual for details on speaker installation. Speakers (Optional accessories) 1 2 1 AC cord connection (see page 12) ­ AC cord fixing 1 2 Speaker terminal (R, L) Close Push until the hook clicks. Unplug the AC cord Unplug the AC cord pressing the two knobs. 1 Plug the AC cord into 2 Note: Make sure that the AC cord is locked on both the left and right sides. the display unit. 2 Fix the AC cord with the clamper which is attached to the unit. Note: When disconnecting the AC cord, be absolutely sure to disconnect the AC cord plug at the socket outlet first. ­ Cable fixing band Secure any excess cables with band as required. Note: One fixing band is supplied with this unit. In case of securing cables at two positions, please purchase it separately. Pass the attached cable fixing band through the clip as shown in the figure. To secure cables connected to Terminals, wrap the cable fixing band around them then pass the pointed end through the locking block, as shown in the figure. While ensuring there is sufficient slack in cables to minimize stress (especially in the power cord), firmly bind all cables with the supplied fixing band. To tighten: Pull To loosen: Push the catch 1 2 Pull INPUT1: Video input terminal INPUT2: S Video input terminal INPUT3: Component/RGB Video input terminals Connect a video device such as VCR or DVD player. (see page 11) INPUT4: PC input terminal From EXTERNAL monitor terminal on computer (see page 9) From SERIAL terminal on computer (see page 10) From audio output terminal on external equipment connected to INPUT1 to 4 (see page 9, 11) 8 Connections PC Input Terminals connection (Female) COMPUTER Conversion adapter (if necessary) RGB PC cable Mini D-sub 15p (Male) Audio Connect a cable which matches the audio output terminal on the computer. Stereo plug Notes: · Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1, 200 lines. ) · The display resolution is a maximum of 768 × 768 dots (TH-42PD12U), 1, 024 × 768 dots (TH-50PD12U) when the aspect mode is set to "4:3", and 1, 024 × 768 dots (TH-42PD12U), 1, 366 × 768 dots (TH-50PD12U) when the aspect mode is set to "FULL". If the display resolution exceeds these maximums, it may not be possible to show fine detail with sufficient clarity. · The PC input terminals are DDC2B-compatible. If the computer being connected is not DDC2B-compatible, you will need to make setting changes to the computer at the time of connection. · Some PC models cannot be connected to the set. · There is no need to use an adapter for computers with DOS/V compatible Mini D-sub 15P terminal. · The computer shown in the illustration is for example purposes only. · Additional equipment and cables shown are not supplied with this set. · Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified frequency range. [. . . ] Marking or retained images (sometimes called "burn-in") resulting from the display of fixed images on video display products are not defects and are not covered under this warranty. THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES. In certain instances, some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, or the exclusion of implied warranties, so the above limitations and exclusions may not be applicable. [. . . ]