User manual PANASONIC TH50PF9UK-EN

[. . . ] Operating Instructions High Definition Plasma Display Model No. TH-50PF9UK The illustration shown is an image. Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference. English TQBC2140-1 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: To reduce the risk of electric shock, do not remove cover or back. Refer servicing to qualified service personnel. The lightning flash with arrow-head within a triangle is intended to tell the user that parts inside the product are a risk of electric shock to persons. [. . . ] When exiting the mode, the screen will return to a former adjustment. H-POS H-SIZE V-POS V-SIZE 1:1 PIXEL MODE 0 0 0 0 OFF During "COMPONENT", "RGB" and "PC" input signal. POS. /SIZE NORMALIZE NORMAL AUTO SETUP H-POS H-SIZE V-POS V-SIZE DOT CLOCK CLOCK PHASE 1:1 PIXEL MODE 0 0 0 0 0 0 OFF Helpful Hint ( / NORMALIZE Normalization) While the POS. /SIZE display is active, if either the N button on the remote control is pressed at any time or the ACTION ( ) button is pressed during "NORMALIZE", then all adjustment values are returned to the factory settings. 20 Adjusting POS. /SIZE AUTO SETUP Automatically adjust H-POS / V-POS / CLOCK PHASE / DOT CLOCK and set H-SIZE / V-SIZE the standard value when RGB signal is input. Notes: · If the dot clock frequency is 162 MHz or higher, DOT CLOCK cannot be made. · If the image is that the edge is hardly figured out or shadowy, that cannot be adjusted automatically. In such case, press AUTO SETUP again after changing the image to the clearer one. · When DVI-D is input, CLOCK PHASE cannot be adjusted automatically. /SIZE and press the ACTION ( ) button when appropriate adjustment cannot be made. Adjust the horizontal position. H-POS H-SIZE Adjust the horizontal size. V-POS Adjust the vertical position. V-SIZE Adjust the vertical size. DOT CLOCK (During "COMPONENT", "RGB" and "PC" input signal) Periodic striped pattern interference (noise) may occur when a striped pattern is displayed. If this happens, adjust so that any such noise is minimized. (During "COMPONENT", "RGB" and "PC" input signal) Eliminate the flickering and distortion. CLOCK PHASE 1:1 PIXEL MODE Adjusts the display size when 1125i, 1125p or 1250i signal is input. Notes: · Select ON when you would like to replay 1920 × 1080 input signal. · Applicable input signal; 1125 / 50i · 60i · 24sF · 24p · 25p · 30p · 50p · 60p , 1250 / 50i · Select OFF when flickering is shown around the image. · H-SIZE, V-SIZE and DOT CLOCK cannot be adjusted when ON is selected. OFF ON Helpful Hint ( / NORMALIZE Normalization) While the POS. /SIZE display is active, if either the N button on the remote control is pressed at any time or the ACTION ( ) button is pressed during "NORMALIZE", then all adjustment values are returned to the factory settings. 21 MULTI PIP Press repeatedly. Each time pressing this button main picture and sub picture will be displayed as follows below. [Picture and Picture] Main picture MULTI PIP [Picture out Picture] Main picture Sub picture [Picture in Picture] Main picture Sub picture Sub picture Normal Viewing MULTI PIP MULTI PIP A B SWAP A SWAP B A B SWAP Press to swap main picture and sub picture. B A B A B A Sub picture label is bright [Example] Main picture label is bright Press to select the input mode. Under main Picture and sub picture display, select the SELECT picture which you would like to change input modes. Notes: · The sub picture sound is heard while a sub picture B B operation is underway. Input modes switching is possible · The sub picture operation automatically returns to Main picture label is changed Sub picture label is changed the main picture operation if a sub picture operation has not been performed for about 5 seconds or if any of the remote control buttons is pressed (except button). PC1 VIDEO2 PC1 VIDEO2 A A C VIDEO2 VIDEO1 Press to change input signal. B A PC1 VIDEO2 D Picture is changed Press to move the sub picture. Each time the location of the sub picture will be moved. Notes: · This button is effective only in the picture in picture. [. . . ] THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES. In certain instances, some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, or the exclusion of implied warranties, so the above limitations and exclusions may not be applicable. WARRANTY COVERAGE PERIOD EXCEPTIONS Item Video Tape P2 Cards Video Heads D5 Video heads Maintenance Items Colour Camera CCD Imaging Block LCD/CRT Monitors * DLPTM Projectors * LCD Projectors above 2, 500 ANSI Lumens * LCD Projectors below 2, 500 ANSI Lumens Projector Lamps Plasma Displays Hard Drive Disk Unit Parts 30 days--Replacement only (content not covered) (Content not covered) 1 year or 2, 000 hrs. [. . . ]