User manual PANASONIC TH50PF9UK-SP

[. . . ] The exclamation point within a triangle is intended to tell the user that important operating and servicing instructions are in the papers with the appliance. WARNING : To prevent damage which may result in fire or shock hazard, do not expose this apparatus to rain or moisture. Do not place containers with water (flower vase, cups, cosmetics, etc. ) above the set. (including on shelves above, etc. ) WARNING : 1) To prevent electric shock, do not remove cover. Refer servicing to qualified service personnel. [. . . ] Certain 4:3 program material, such as stock market data screens, may occasionally cause the image size to change unexpectedly. When viewing such programs, it is recommended that the ASPECT be set to NORMAL. · If adjusting the PICTURE V-POS/V-SIZE in Panasonic AUTO with FULL mode, the adjustment is not memorized. When exiting the mode, the screen will return to a former adjustment. · Panasonic AUTO can not be selected while TY-FB9BD (optional BNC Dual Video Terminal Board) is installed. 4 3 16 Panasonic AUTO 9 Panasonic AUTO For an elongated image 4 3 Image is expanded Changes in accordance with the Panasonic AUTO mode setting (see page 38). For a 4:3 image Note: Do not allow the picture to be displayed in NORMAL mode for an extended period, as this can cause a permanent after-image to remain on the Plasma Display Panel. 19 Adjusting POS. Press to select AUTO SETUP / H-POS / H-SIZE / V-POS / V-SIZE / DOT CLOCK / CLOCK PHASE / 1:1 PIXEL MODE 3 Press to adjust POS. /SIZE. During "VIDEO (S VIDEO)", "Digital", "SDI" and "HDMI" input signal. POS. /SIZE 4 Press to exit from adjust mode. NORMALIZE NORMAL AUTO SETUP Notes: · Adjustment details are memorized separately for different input signal formats (Adjustments for component signals are memorized for 525 (480) / 60i · 60p, 625 (575) / 50i · 50p, 1125 (1080) / 60i · 50i · 60p · 50p · 24p · 25p · 30p · 24sF, 1250 (1080) / 50i, 750 (720) / 60p · 50p each, and RGB/PC/Digital signals are memorized for each frequency. ) · If a "Cue" or "Rew" signal from a VCR or DVD player is received, the picture position will shift up or down. This picture position movement cannot be controlled by the POS. · If adjusting the PICTURE V-POS / V-SIZE in Panasonic AUTO with FULL mode, the adjustment is not memorized. When exiting the mode, the screen will return to a former adjustment. H-POS H-SIZE V-POS V-SIZE 1:1 PIXEL MODE 0 0 0 0 OFF During "COMPONENT", "RGB" and "PC" input signal. POS. Notes: · Sound output is from the picture which is selected in Audio OUT(PIP) (See page 26). · In 2 screen display, the same input mode cannot be selected for the main picture and sub picture. · The main picture and sub picture are processed by different circuits, resulting in a slight difference in the clarity of the pictures. There may also be a difference in the picture quality of the sub picture depending on the type of signals displayed on the main picture and depending on the 2-picture display mode. · Due to the small dimensions of the sub pictures, these sub pictures cannot be shown in detail. · Computer screen picture is displayed in a simplified format, and it may not be possible to discern details on them satisfactorily. · Following combinations of two analog signals cannot be displayed simultaneously; Component - Component, Component - PC (RGB), PC (RGB) - Component, PC (RGB) - PC (RGB) · Following signals are not applicable to this menu. 1125 / 50p · 60p, 1152 × 864 @60 Hz, 1400 × 1050 @60 Hz, 1600 × 1200 @60Hz, 1920 × 1200 @60 Hz 22 Advanced PIP 1 2 Press to display the Setup menu. Press to select "OSD Language". 3 4 Press and hold until the Options menu is displayed. Press to select Advanced PIP. Options 1/3 Enable On Off Off 0 Off 0 Off Off Off Off 5 Press to adjust the menu. Off : Sets normal two screen display mode (see page 22). [. . . ] For products requiring routine preventive maintenance, that maintenance must be performed in order to maintain warranty coverage. Serial numbers that have been altered, defaced or removed void this warranty. This warranty does not cover replacements or repairs necessitated by loss or damage resulting from any cause beyond the control of PCI. Marking or retained images (sometimes called "burn-in") resulting from the display of fixed images on video display products are not defects and are not covered under this warranty. [. . . ]