User manual PANASONIC TH-50PH12U

[. . . ] Operating Instructions Manual de instrucciones High Definition Plasma Display Alta definición Pantalla de plasma Model No. de Modelo TH-42PH12U TH-50PH12U TH-42PH12L TH-50PH12L Contents Important Safety Instructions ··········································· 3 FCC STATEMENT ······························································· 4 Safety Precautions ···························································· 5 Maintenance ······································································· 6 Accessories ······································································· 7 Connections ······································································· 8 Power ON / OFF ······························································· 14 Selecting the input signal ··············································· Basic Controls ································································· On-Screen Menu Displays ·············································· Specifications ·································································· Panasonic Professional Flat Panel Display Limited Warranty ·· LIMITED WARRANTY STATEMENT ································ Customer Service ···························································· 16 17 19 20 22 23 24 The illustration shown is an image. Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference. [. . . ] Always use new batteries when replacing the old set. Do not combine a used battery with a new one. Do not mix battery types (example: "Zinc Carbon" with "Alkaline"). Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries. Battery replacement is necessary when the remote control acts sporadically or stops operating the Plasma Display. Batteries must not be exposed to excessive heat such as sunshine, fire or the like. 7 Connections For TH-42PH12U, TH-50PH12U When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker's Installation Manual for details on speaker installation. Speakers (Optional accessories) 1 2 1 Speaker terminal (R) Speaker terminal (L) AC cord connection (see page 14) ­ AC cord fixing 1 2 Close Push until the hook clicks. Keep the knob pressed. Unplug the AC cord Unplug the AC cord pressing the two knobs. 1 Plug the AC cord into 2 Note: Make sure that the AC cord is locked on both the left and right sides. the display unit. 2 Fix the AC cord with the clamper which is attached to the unit. Note: When disconnecting the AC cord, be absolutely sure to disconnect the AC cord plug at the socket outlet first. ­ Cable fixing band Secure any excess cables with band as required. Note: One fixing band is supplied with this unit. In case of securing cables at two positions, please purchase it separately. Pass the attached cable fixing band through the clip as shown in the figure. To secure cables connected to Terminals, wrap the cable fixing band around them then pass the pointed end through the locking block, as shown in the figure. While ensuring there is sufficient slack in cables to minimize stress (especially in the power cord), firmly bind all cables with the supplied fixing band. To tighten: Pull To loosen: Push the catch 1 2 R AUDIO L PR/CR/R PB/CB/B Y/G Pull AUDIO COMPONENT/RGB IN SLOT1 SLOT2 SLOT3 PC IN SERIAL Optional Terminal Board Insert Slot (covered) Dual HDMI Terminals (equivalent of Dual HDMI Terminal Board (TYFB10HMD)) (see page 12) COMPONENT/RGB IN and Audio IN Terminals (equivalent of BNC Component Video Terminal Board (TY-42TM6A)) (see page 13) From EXTERNAL monitor terminal on Computer (see page 10) From SERIAL Terminal on Computer (see page 11) Note: At factory shipment, Terminal boards are installed in SLOT 2 and SLOT 3. 8 Connections For TH-42PH12L, TH-50PH12L When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker's Installation Manual for details on speaker installation. Speakers (Optional accessories) 1 2 1 Speaker terminal (R) Speaker terminal (L) AC cord connection (see page 14) ­ AC cord fixing 1 2 Close Push until the hook clicks. Keep the knob pressed. Unplug the AC cord Unplug the AC cord pressing the two knobs. 1 Plug the AC cord into 2 Note: Make sure that the AC cord is locked on both the left and right sides. the display unit. 2 Fix the AC cord with the clamper which is attached to the unit. Note: When disconnecting the AC cord, be absolutely sure to disconnect the AC cord plug at the socket outlet first. ­ Cable fixing band Secure any excess cables with band as required. Note: One fixing band is supplied with this unit. In case of securing cables at two positions, please purchase it separately. Pass the attached cable fixing band through the clip as shown in the figure. [. . . ] Marking or retained images (sometimes called "burn-in") resulting from the display of fixed images on video display products are not defects and are not covered under this warranty. THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES. In certain instances, some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, or the exclusion of implied warranties, so the above limitations and exclusions may not be applicable. [. . . ]