User manual PANASONIC TH-50PH20U

[. . . ] de Modelo TH-42PH20U TH-50PH20U Operating Instructions High Definition Plasma Display Contents · Important Safety Instructions . . . . . . . . . . . . . . . . . . 3 4 · FCC STATEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . · Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Always use new batteries when replacing the old set. Do not combine a used battery with a new one. Do not mix battery types (example: "Zinc Carbon" with "Alkaline"). Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries. Battery replacement is necessary when the remote control acts sporadically or stops operating the Plasma Display. Batteries must not be exposed to excessive heat such as sunshine, fire or the like. 7 Connections Speaker connection When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker's Installation Manual for details on speaker installation. Speakers (Optional accessories) 1 Red Black While pressing the lever, insert the core wire. 2 Speaker terminal (L) Speaker terminal (R) AC cord connection (see page 13) Black Red Return the lever. AC cord connection and fixing, cable fixing AC cord fixing Unplug the AC cord Using the clamper Secure any excess cables with clamper as required. Unplug the AC cord pressing the two knobs. When disconnecting the AC cord, be Note: Make sure that the AC cord is locked on absolutely sure to disconnect the AC both the left and right sides. When using the Wall-hanging bracket (vertical) Note: When using the Wall-hanging bracket (vertical) (TY-WK42PV20), use the holes and to secure the cables. If the clamper is used on the hole , the cables may be caught by the wall-hanging bracket. 1 Attach the clamper hole To remove from the unit: snaps 2 Bundle the cables To loosen: Insert the clamper in a hole. Keep pushing both side snaps hooks Set the tip in the hooks knob Keep pushing the knob 8 Connections Video equipment connection PC IN: PC Input Terminal Connect to video terminal of PC or equipment with Y, PB(CB) and PR(CR) output. (see page 11) SERIAL: Control the Plasma Display by connecting to PC. (see page 12) SLOT: Terminal board (optional Note: accessories) insert slot (see page 5) The right side slot is for terminal board with 2-slot width. The terminal board with 1-slot width does not function when installed in the right side slot. Terminals are on the bottom side of the Plasma Display. AV IN (VIDEO): Composite Video Input Terminal (see below) COMPONENT/RGB IN: Component/RGB Video Input Terminal (see below) AV IN (HDMI): HDMI Input Terminal (see page 10) DVI-D IN: DVI-D Input Terminal (see page 10) Connect to video equipment such as VCR or DVD player. VIDEO and COMPONENT / RGB IN connection Note: Additional equipment, cables and adapter plugs shown are not supplied with this set. L R AUDIO OUT VIDEO OUT VCR RCA-BNC Adapter plug RCA-BNC Adapter plug Notes: · Change the "COMPONENT/RGB-IN select" setting in the "SETUP" menu to "COMPONENT" (when COMPONENT signal connection) or "RGB" (when RGB signal connection). · Accepts only RGB signals with "SYNC ON G". DVD Player Y PB PR L R AUDIO OUT Computer Y, PB, PR, OUT RGB Camcorder 9 Connections HDMI connection [Pin assignments and signal names] Pin No. 1 2 3 4 5 6 7 8 9 10 Signal Name T. M. D. S Data2+ T. M. D. S Data2 Shield T. M. D. S Data2T. M. D. S Data1+ T. M. D. S Data1 Shield T. M. D. S Data1T. M. D. S Data0+ T. M. D. S Data0 Shield T. M. D. S Data0T. M. D. S Clock+ Pin No. 11 12 13 14 15 16 17 18 19 Signal Name T. M. D. S Clock Shield T. M. D. S ClockCEC Reserved (N. C. on device) SCL SDA DDC/CEC Ground +5V Power Hot Plug Detect 19 31 HDMI cable 18 42 HDMI AV OUT DVD player Note: Additional equipment and HDMI cable shown are not supplied with this set. DVI-D IN connection PC with DVI-D video out Stereo mini plug (M3) DVI-video cable (Within 5 m) DVI-D Input Connector Pin Layouts Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 Signal Name T. M. D. S. data 2 shield Pin No. 13 14 15 16 17 18 19 20 21 22 23 24 Signal Name +5 V DC Ground Hot plug detect T. M. D. S. data 0 shield 1 9 17 8 16 24 DDC clock DDC data T. M. D. S. data 1 shield Connection port view Notes: · Additional equipment and cables shown are not supplied with this set. · Use the DVI-D cable complying with the DVI standard. Image deterioration may occur depending on the length or the quality of the cable. T. M. D. S. clock- 10 Connections PC Input Terminals connection (Female) COMPUTER Audio Stereo mini plug (M3) Connect a cable which matches the audio output terminal on the computer. [. . . ] This warranty does not cover replacements or repairs necessitated by loss or damage resulting from any cause beyond the control of PCI. Marking or retained images (sometimes called "burn-in") resulting from the display of fixed images on video display products are not defects and are not covered under this warranty. THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES. [. . . ]