User manual PANASONIC TH-50PHD5EX

[. . . ] ® High Definition Plasma Display PLASMA DISPLAY + -- INPUT VOL POWE R / BY R - STAND ON G POWER Operating Instructions TH-42PHD5 Model No. TH-50PHD5 Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference. English TQBC0467-1 Dear Panasonic Customer Welcome to the Panasonic family of customers. We hope that you will have many years of enjoyment from your new High Definition Plasma Display. [. . . ] (2) The computer shown is for example purposes only. (3) Additional equipment and cables shown are not supplied with this set. The SERIAL terminal conforms to the RS-232C interface specification, so that the Plasma Display can be controlled by a computer which is connected to this terminal. The computer will require software which allows the sending and receiving of control data which satisfies the conditions given below. Use a computer application such as a programming language to software. Refer to the documentation for the computer application for details. Communication parameters Signal level Synchronization method Baud rate Parity Character length Stop bit Flow control RS-232C compliant Asynchronous 9600 bps None 8 bits 1 bit RS-232C Conversion cable Details D-sub 9-pin female RXD 2 TXD 3 5 GND Non use 46 7 8 1·9 Shorted NC Basic format for control data The transmission of control data from the computer starts with a STX signal, followed by the command, the parameters, and lastly an ETX signal in that order. If there are no parameters, then the parameter signal does not need to be sent. STX C1 C2 C3 : P1 P2 P3 P4 P5 ETX End (03h) Command Command PON POF AVL AMT IIS Parameter None None Control details Power ON Power OFF Volume 00 - 63 Audio mute OFF Audio mute ON Input select (toggle) AV Mode Component / RGB mode (processed as a Y/PB/PR or RGB signals as set by this unit) PC Mode Screen mode select (toggle) 4:3 Zoom 16 : 9 Just Panasonic Auto ** Start (02h) Colon Parameter(s) (1 - 5 bytes) 3-character command (3bytes) 0 1 None VID YP1 RG1 None NORM ZOOM FULL JUST SELF Notes: (1) If multiple commands are transmitted, be sure to wait for the response for the first command to come from this unit before sending the next command. (2) If an incorrect command is sent by mistake, this unit will send an "ER401" command back to the computer. DAM With the power off, this display responds to PON command only. 12 Basic Controls Explanations from here onward describe the functions when the optional BNC Terminal Board is installed. R - STANDBY G POWER ON TH-50PHD5 INPUT -- VOL + Main Power On/Off Switch Power Indicator The Power Indicator will light. Indicator not illuminated (The unit will still consume some power as long as the power cord is still inserted into the wall outlet. ) Stand-by . . . . . . Green INPUT button (AV(S Video), Component/RGB and PC Mode Selection) Press the "INPUT" button to select AV (S Video), Component/RGB and PC input signal modes sequentially. (see page 15) · · · Volume Adjustment Press the Volume Up "+" or Down "­" button to increase or decrease the sound volume level. Stand-by (ON/OFF) button The Plasma Display must first be plugged into the wall outlet and turnded on at the power switch. (see page 14) Press this button to turn the Plasma Display On, from Standby mode. Press it again to turn the Plasma Display Off to Standby mode. Status button Press the "Status" Button to display the current system status. AV 4:3 SURROUND button (see page 23) INPUT button AV(S Video), Component/RGB and PC Mode Selection) Press to select AV(S Video), Component/RGB and PC input signal modes sequentially. (see page 15) INPUT 1 2 Sound mute On/Off (see page 22) Volume Adjustment Press the Volume Up "+" or Down "­" Button to increase or decrease the sound volume level. R button (see page 17) ACTION button Press to make selections POSITION buttons SET UP button (see page 16) SOUND button (see page 22) Off timer 90 3 SURROUND 1 AV(S Video), Component/RGB, PC mode 2 Aspect mode (see page 18) 3 Off timer The off timer indicator is displayed only when the off timer has been set. N button (see page 21, 22, 24, 25) VOL N R PICTURE SOUND SET UP PICTURE button (see page 24) PICTURE POS. /SIZE ASPECT PICTURE POS. /SIZE button (see page 20) PC OFF TIMER ASPECT button Press to adjust the aspect. (see page 18) PC button Press the "PC" mode selection button to select the PC mode. OFF TIMER button This button is used to switch The Plasma Display can be preset to switch to stand-by after a fixed period. The setting changes to 30 minutes, 60 minutes, 90 minutes and 0 minutes (off timer cancelled) each time the button is pressed. [. . . ] Display range: Horizontal 15. 6 - 110 kHz Vertical 48 - 120 Hz H-Freq. V-Freq. 31. 5 kHz 60. 0 Hz 32 Troubleshooting Before you call for service, determine the symptoms and make a few simple checks as shown below. Symptoms Picture Sound Checks Electrical Appliances Cars/Motorcycles Fluorescent light Interference Noisy Sound Volume (Check whether the mute function has been activated on the remote control. ) Normal Picture No Sound Not plugged into AC outlet Not switched on Picture and Brightness/Volume setting (Check by pressing the power switch or standby button on the remote control. ) If a signal with a non-applicable colour system format, or frequency is input, only the input terminal indication is displayed. No Picture Normal Sound Colour controls set at minimum level (see page 24, 25) Colour system (see page 31) No Colour Plasma Display panel Symptoms Check Normal Sound No Picture No Sound Some parts of the screen do not light up The plasma display panel is manufactured using an extremely high level of precision technology, however, sometimes some parts of the screen may be missing picture elements or have luminous spots. This is not a malfunction. Do not allow a still picture to be displayed for an extended period, as this can cause a permanent after-image to remain on the Plasma Display. [. . . ]