User manual PANASONIC TH-50PHD5HY

[. . . ] ® High Definition Plasma Display PLASMA DISPLAY + -- INPUT VOL POWE R / BY R - STAND ON G POWER Operating Instructions TH-42PHD5 Model No. TH-50PHD5 Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference. English TQBC0480-1 Dear Panasonic Customer Welcome to the Panasonic family of customers. We hope that you will have many years of enjoyment from your new High Definition Plasma Display. [. . . ] (3) The PC input terminals are DDC1/2B-compatible. If the computer being connected is not DDC1/2B-compatible, you will need to make setting changes to the computer at the time of connection. (4) Some PC models cannot be connected to the set. (5) There is no need to use an adapter for computers with DOS/V compatible D-sub 15P terminal. (6) The computer shown in the illustration is for example purposes only. (7) Additional equipment and cables shown are not supplied with this set. (8) Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified frequency range. 13 Connections Signal Names for D-sub 15P Connector 11 12 13 14 15 6 1 7 2 8 3 9 10 4 5 Pin Layout for PC Input Terminal Pin No. 1 2 3 4 5 Signal Name R G B GND (Ground) GND (Ground) Pin No. 6 GND (Ground) 11 7 GND (Ground) 12 8 GND (Ground) 13 9 NC (not connected) 14 10 GND (Ground) 15 Signal Name GND (Ground) SDA HD/SYNC VD SCL AV/Component/RGB/PC/DVI input signals AUDIO R AUDIO IN L S VIDEO IN VIDEO IN VIDEO OUT R AUDIO L VD HD PR/CR/R PB/CB/B Y/G AV COMPONENT/RGB IN PC IN SERIAL AV input AV input signal name 1 2 3 4 5 NTSC PAL PAL60 SECAM Modified NTSC Component/RGB input horizontal frequency(kHz) 15. 734 15. 625 15. 734 15. 625 15. 734 horizontal frequency(kHz) 15. 734 15. 625 31. 468 31. 25 45 33. 75 28. 125 27 27 31. 5 31. 5 35 37. 5 31. 7 37. 9 46. 9 53. 7 49. 7 48. 4 56. 5 60 68. 7 68. 7 64 80 91. 1 75 vertical frequency(Hz) 59. 95 50 59. 95 50 59. 95 vertical frequency(Hz) 59. 94 50 59. 94 50 60 60 50 24 48 70 59. 94 67 75 60 60 75 85 75 60 70 75 85 75 60 75 85 60 PC RGB input Component/RGB/PC/DVI input signal name 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 525 (480) /60i 625 (575) /50i 525 (480) /60p 625 (575) /50p 750 (720) /60p 1, 125 (1, 080) /60i 1, 125 (1, 080) /50i 1, 125 (1, 080) /24p 1, 125 (1, 080) /24sF 640 × 400 @70 640 × 480 @60 Macintosh13" (640 × 480) 640 × 480 @75 852 × 480 @60 800 × 600 @60 800 × 600 @75 800 × 600 @85 Macintosh16" (832 × 624) 1, 024 × 768 @60 1, 024 × 768 @70 1, 024 × 768 @75 1, 024 × 768 @85 Macintosh21" (1, 152 × 870) 1, 280 × 1, 024 @60 1, 280 × 1, 024 @75 1, 280 × 1, 024 @85 1, 600 × 1, 200 @60 Component RGB PC DVI Mark: By installing the RGB(digital)Terminal Board(TY-42TM4D) to this set the PC input signal can be displayed. 14 Connections SERIAL Terminals connection The SERIAL terminal is used when the Plasma Display is controlled by a computer. COMPUTER 6 7 2 3 8 4 9 5 1 SERIAL RS-232C straight cable Ferrite core (large size) (supplied) Pin layout for RS-232C Installing the ferrite core (Large size) D-sub 9p Less than 3" 15/16 (10 cm) Open Notes: (1) Use the RS-232C cable to connect the computer to the Plasma Display. (2) The computer shown is for example purposes only. (3) Additional equipment and cables shown are not supplied with this set. The SERIAL terminal conforms to the RS-232C interface specification, so that the Plasma Display can be controlled by a computer which is connected to this terminal. The computer will require software which allows the sending and receiving of control data which satisfies the conditions given below. Use a computer application such as programming language software. Refer to the documentation for the computer application for details. Communication parameters Signal level Synchronization method Baud rate Parity Character length Stop bit Flow control RS-232C compliant Asynchronous 9600 bps None 8 bits 1 bit RS-232C Conversion cable D-sub 9-pin female Details RXD 2 TXD 3 GND 5 Non use 46 7 8 1·9 Shorted NC Basic format for control data The transmission of control data from the computer starts with a STX signal, followed by the command, the parameters, and lastly an ETX signal in that order. If there are no parameters, then the parameter signal does not need to be sent. STX C1 C2 C3 : P1 P2 P3 P4 P5 ETX End (03h) Command Command PON POF AVL AMT IIS Parameter None None Control details Power ON Power OFF Volume 00 - 63 Audio mute OFF Audio mute ON Input select (toggle) AV Mode Component / RGB mode (processed as a Y/PB/PR or RGB signals as set by this unit) PC Mode Screen mode select (toggle) 4:3 Zoom 16 : 9 Just Panasonic Auto ** Start (02h) Colon Parameter(s) (1 - 5 bytes) 3-character command (3bytes) 0 1 None VID YP1 RG1 None NORM ZOOM FULL JUST SELF Notes: (1) If multiple commands are transmitted, be sure to wait for the response for the first command to come from this unit before sending the next command. (2) If an incorrect command is sent by mistake, this unit will send an "ER401" command back to the computer. DAM With the power off, this display responds to PON command only. 15 Basic Controls R - STANDBY G POWER ON TH-50PHD5 INPUT -- VOL + Main Power On/Off Switch Power Indicator The Power Indicator will light. Indicator not illuminated (The unit will still consume some power as long as the power cord is still inserted into the wall outlet. ) Stand-by . . . . Green INPUT button (AV(S Video), Component/RGB and PC Mode Selection) Press the "INPUT" button to select AV (S Video), Component/RGB and PC input signal modes sequentially. (see page 19) · · · Volume Adjustment Press the Volume Up "+" or Down "­" button to increase or decrease the sound volume level. Stand-by (ON/OFF) button The Plasma Display must first be plugged into the wall outlet and turnded on at the power switch (see page 18). Press this button to turn the Plasma Display On, from Stanby mode. [. . . ] · 525i(480i) signal input during "Component" input signal mode. R (ACTION) button [ AV ] On Auto Off 4:3 Signal 3D Y/C Filter (NTSC) Colour system 3:2 Pulldown Panasonic Auto (4:3 ) Press to exit from adjust mode. Signal 3:2 Pulldown [ Component ] Off 35 Setup for Input Signals Sync Setup Select Signal from the "Setup" menu during RGB or PC input signal mode. Component/RGB-in select RGB Signal Screensaver OSD Language Set up TIMER English (UK) Press to adjust. Press (ACTION) button [ RGB ] H&V Signal Sync R Press to exit from adjust mode. Signal Sync H-Freq. V-Freq. 31. 5 kHz 60. 0 Hz [ PC ] H&V H-Freq. 31. 5 kHz 60. 0 Hz Setting RGB sync signal: Confirm that the input is set to RGB input (this setting is valid only for RGB input). H & V: The H and V sync signals are input from the HD/VD connector. [. . . ]