User manual PANASONIC TH-50PHW5HZ

[. . . ] ® High Definition Plasma Display PLASMA DISPLAY + -- INPUT VOL POWE R / BY R - STAND ON G POWER Operating Instructions TH-42PHW5 Model No. TH-50PHW5 Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference. English TQBC0475-1 Dear Panasonic Customer Welcome to the Panasonic family of customers. We hope that you will have many years of enjoyment from your new High Definition Plasma Display. [. . . ] Furthermore, do not leave it for long periods in contact with articles made from rubber or PVC. 6 Accessories Accessories Supply Check that you have the accessories and items shown Operating Instruction book Remote Control Transmitter EUR646525 INPUT SURROUND Batteries for the Remote Control Transmitter (2 × R6 Size) Guarantee Card VOL N R PICTURE SOUND SET UP PICTURE POS. (Example) When connecting an S VIDEO VCR. (S VIDEO VCR) R Audio OUT L Video OUT S Video OUT S VIDEO 4 pin socket Luminance earth Chrominance earth 2×RCA audio cables AUDIO Audio input to L/R sockets S VIDEO Video input to S VIDEO socket Luminance in Chrominance in R AUDIO L VIDEO S VIDEO AV IN (Example) When connecting 3×RCA audio video cables. (VCR) R Audio OUT L Video OUT AUDIO-VIDEO Video input to RCA socket 3×RCA audio video cables Audio input to L/R sockets R AUDIO L VIDEO S VIDEO AV IN Note: Additional equipment and cables shown are not supplied with this set. 10 Connections (Example) When connecting 21 pin scart cables. (VCR) AV2 Video input to BNC socket BNC-RCA adaptor plug (DVD / Satellite Receiver) Audio input to L/R sockets R AUDIO L VIDEO S VIDEO AV1/TV AV IN Video input to RCA socket Notes: (1) Additional equipment, cables and an adaptor plug shown are not supplied with this set. (2) 21 pin connectors and 21 pin scart plugs are connectors used in Europe. Audio input to L/R sockets Component/RGB Input connection Component signals (Y, PB, PR) connection (DVD Player) Y Y, PB, PR PB PR 3×RCA video cables AUDIO 2×RCA audio cables L R R AUDIO L VD HD PR/CR/R PB/CB/B Y/G COMPONENT/RGB IN Notes: (1) Change the "Component/RGB-in" setting in the "Setup" menu to "Component". (see page 32) (2) Additional equipment and cables shown are not supplied with this set. 11 Connections RGB signal (R, G, B, HD, VD) connection RGB input to R, G, B, HD, VD sockets Example of input signal source HDTV-compatible VCR BNC-RCA adaptor plug 5×BNC RGB cables RGB camera R AUDIO L VD HD PR/CR/R PB/CB/B Y/G COMPONENT/RGB IN AUDIO 2×RCA audio cables Audio input to L/R sockets Computer VD HD R B G Notes: (1) Change the "Component/RGB-in" setting in the "Setup" menu to "RGB". (see page 32) (2) Additional equipment, cables and adaptor plugs shown are not supplied with this set. 12 Connections PC Input Terminals connection COMPUTER AUDIO PC IN POWER / R - STANDBY G POWER ON INPUT ­ VOL + Conversion adapter (if necessary) Less than 3" 15/16 (10 cm) Ferrite core (large size) (supplied) D-sub 15p RGB PC cable Ferrite core (small size) (supplied) Less than 3" 15/16 (10 cm) Audio Stereo plug Connect a cable which matches the audio output terminal on the computer. Installing the ferrite core (Small size) 1 2 Open Press the cable through and close 3 Pull back the tabs (in two places) Installing the ferrite core (Large size) 1 2 Open Press the cable through and close 3 Pull back the tabs (in two places) Notes: (1) Computer signals which can be input are those with a horizontal scanning frequency of 15. 6 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1, 200 lines. ) (2) The display resolution is a maximum of 768 × 768 dots (TH-42PHW5) / 1, 024 × 768 dots (TH-50PHW5) when the aspect mode is set to "4:3", and 1, 024 × 768 dots (TH-42PHW5) / 1, 366 × 768 dots (TH-50PHW5) when the aspect mode is set to "16:9". If the display resolution exceeds these maximums, it may not be possible to show fine detail with sufficient clarity. (3) The PC input terminals are DDC1/2B-compatible. If the computer being connected is not DDC1/2B-compatible, you will need to make setting changes to the computer at the time of connection. (4) Some PC models cannot be connected to the set. (5) There is no need to use an adapter for computers with DOS/V compatible D-sub 15P terminal. (6) The computer shown in the illustration is for example purposes only. (7) Additional equipment and cables shown are not supplied with this set. (8) Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified frequency range. 13 Connections Signal Names for D-sub 15P Connector 11 12 13 14 15 6 1 7 2 8 3 9 10 4 5 Pin Layout for PC Input Terminal Pin No. 1 2 3 4 5 Signal Name R G B GND (Ground) GND (Ground) Pin No. 6 GND (Ground) 11 7 GND (Ground) 12 8 GND (Ground) 13 9 NC (not connected) 14 10 GND (Ground) 15 Signal Name GND (Ground) SDA HD/SYNC VD SCL AV/Component/RGB/PC input signals AUDIO R AUDIO L VIDEO S VIDEO R AUDIO L VD HD PR/CR/R PB/CB/B Y/G AV IN COMPONENT/RGB IN PC IN SERIAL AV input AV input signal name 1 2 3 4 5 NTSC PAL PAL60 SECAM Modified NTSC Component/RGB input horizontal frequency(kHz) 15. 734 15. 625 15. 734 15. 625 15. 734 horizontal frequency(kHz) 15. 734 15. 625 31. 468 31. 25 45 33. 75 28. 125 27 27 31. 5 31. 5 35 37. 5 31. 7 37. 9 46. 9 53. 7 49. 7 48. 4 56. 5 60 68. 7 68. 7 64 80 91. 1 75 vertical frequency(Hz) 59. 95 50 59. 95 50 59. 95 vertical frequency(Hz) 59. 94 50 59. 94 50 60 60 50 24 48 70 59. 94 67 75 60 60 75 85 75 60 70 75 85 75 60 75 85 60 PC RGB input Component/RGB/PC input signal name 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 525 (480) /60i 625 (575) /50i 525 (480) /60p 625 (575) /50p 750 (720) /60p 1, 125 (1, 080) /60i 1, 125 (1, 080) /50i 1, 125 (1, 080) /24p 1, 125 (1, 080) /24sF 640 × 400 @70 640 × 480 @60 Macintosh13" (640 × 480) 640 × 480 @75 852 × 480 @60 800 × 600 @60 800 × 600 @75 800 × 600 @85 Macintosh16" (832 × 624) 1, 024 × 768 @60 1, 024 × 768 @70 1, 024 × 768 @75 1, 024 × 768 @85 Macintosh21" (1, 152 × 870) 1, 280 × 1, 024 @60 1, 280 × 1, 024 @75 1, 280 × 1, 024 @85 1, 600 × 1, 200 @60 Component RGB PC 14 Connections SERIAL Terminals connection The SERIAL terminal is used when the Plasma Display is controlled by a computer. COMPUTER 1 6 2 7 3 8 4 9 5 RS-232C straight cable Ferrite core (large size) (supplied) SERIAL Pin layout for RS-232C Installing the ferrite core (Large size) D-sub 9p Less than 3" 15/16 (10 cm) Open Notes: (1) Use the RS-232C cable to connect the computer to the Plasma Display. (2) The computer shown is for example purposes only. (3) Additional equipment and cables shown are not supplied with this set. The SERIAL terminal conforms to the RS-232C interface specification, so that the Plasma Display can be controlled by a computer which is connected to this terminal. The computer will require software which allows the sending and receiving of control data which satisfies the conditions given below. Use a computer application such as programming language software. Refer to the documentation for the computer application for details. [. . . ] H & V: The H and V sync signals are input from the HD/VD connector. on G: Uses a synchronized signal on the Video G signal, which is input from the G connector. on VIDEO: Compatible with the scart plug (Europe) The composite video signal input from the VIDEO input terminal is used by dividing the sync signals. Sync H&V Sync on G Sync on VIDEO Setting PC sync signal: Confirm that the input is set to PC input (this setting is valid only for PC input). H & V: The H and V sync signals are input from the HD/VD connector. [. . . ]