User manual PANASONIC TH-50PV600R

[. . . ] Visit our Panasonic Web Site http://panasonic. net Table of Contents Important Safety Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Accessories Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Press to select Periodic Time / Operating Time (When Interval is selected). Screensaver PRESENT TIME 99:99 Start Function Mode Start Time Finish Time Side panel Wobbling Peak limit White bar scroll Time Designation 6:15 12:30 High Off Off Press to Setup. Screensaver PRESENT TIME Start Function Mode Periodic Time Operating Time Side panel Wobbling Peak limit White bar scroll Interval 6:15 12:30 High Off Off 99:99 White bar scroll Time Designation 6:15 12:30 High Off Off Screensaver Press the R button to return to "Setup" menu. PRESENT TIME Start Function Mode Periodic Time Operating Time Side panel Wobbling Peak limit White bar scroll Interval 6:15 12:30 High Off Off 99:99 To setup Multidisplay screen. (See page 33) MULTI DISPLAY Setup MULTI DISPLAY Setup Horizontal Scale Vertical Scale Seam hides video Location Off ×2 ×2 Off A1 To Set up TIMER selection screen (see page 27, 28) Set up TIMER PRESENT TIME POWER ON Function POWER ON Time POWER OFF Function POWER OFF Time Off 0:00 Off 0:00 99:99 Press to select POWER ON Time / POWER OFF Time. Set up TIMER PRESENT TIME POWER ON Function POWER ON Time POWER OFF Function POWER OFF Time Off 0:00 Off 0:00 99:99 Press to Set up POWER ON Time / POWER OFF Time. To PRESENT TIME Setup (see page 27) PRESENT TIME Setup PRESENT TIME Set PRESENT TIME 99:99 99:99 Set up TIMER PRESENT TIME 99:99 Press the R button to return to "Setup" menu. POWER ON Function POWER ON Time POWER OFF Function POWER OFF Time Off 0:00 Off 0:00 17 ASPECT Controls The Plasma Display will allow you to enjoy viewing the picture at its maximum size, including wide screen cinema format picture. Press repeatedly to move through the aspect options: [from the unit] 4:3 Zoom Panasonic Auto 16 : 9 Just INPUT MENU -/ VOL +/ ENTER/ The aspect mode changes each time the ENTER button is pressed. 4:3 16 : 9 [During MULTI PIP Operations] · Picture and Picture, Picture in Picture : · Others : Aspect switching is not possible. Notes: · For PC signal input, the mode switches between "4:3", "Zoom" and "16:9" only. · For a 1125 (1080) / 60i · 50i · 60p · 50p · 24p · 25p · 30p · 24sF, 1250 (1080) / 50i, 750 (720) / 60p · 50p signal input, the mode is set to "16:9" mode, and switching is not possible. · Panasonic Auto can be selected only during Video signal input. · The aspect mode is memorized separately for each input terminal. Mode 4 4:3 Picture Explanation 4:3 will display a 4:3 picture at its standard 4:3 size. 4:3 3 4 16 Zoom Zoom mode magnifies the central section of the picture. 9 Zoom 3 4 16 16 : 9 16:9 will display the picture at its maximum size but with slight elongation. 9 16 : 9 3 4 16 Just Just 3 9 Just mode will display a 4:3 picture at its maximum size but with aspect correction applied to the center of the screen so that elongation is only apparent at the left and right edges of the screen. The size of the picture will depend on the original signal. The display will automatically become enlarged (depending on the picture source), allowing you to view the picture at its maximum size. Notes: · Panasonic Auto mode is designed to automatically adjust the aspect ratio to handle a mix of 16:9 and 4:3 program material. Certain 4:3 program material, such as stock market data screens, may occasionally cause the image size to change unexpectedly. Notes: · Select On when you would like to replay 1920 × 1080 input signal. · Applicable input signal; 1125 / 50i · 60i · 24sF · 24p · 25p · 30p · 50p · 60p · 1250 / 50i · Select Off when flickering is shown around the image. · H-Size, V-Size and Dot Clock cannot be adjusted when On is selected. Clock Phase 1:1 Pixel Mode Off On Helpful Hint ( / Normalise Normalisation) While the Pos. /Size display is active, if either the N button on the remote control is pressed at any time or the ACTION ( ) button is pressed during "Normalise", then all adjustment values are returned to the factory settings. 20 MULTI PIP Press repeatedly. Each time pressing this button main picture and sub picture will be displayed as follows below. [Picture and Picture] Main picture Sub picture [Picture out Picture] Main picture Sub picture [Picture in Picture] Main picture Sub picture Normal Viewing MULTI PIP MULTI PIP MULTI PIP A B SWAP A SWAP B A B SWAP Press to swap main picture and sub picture. B A B A B A Press to select the input mode. Under main Picture and sub picture display, select the picture which you would like to change input modes. Notes: · The sub picture sound is heard while a sub picture operation is underway. · The sub picture operation automatically returns to the main picture operation if a sub picture operation has not been performed for about 5 seconds or if any of the remote control buttons is pressed (except button). Press to change input signal. [Example] Main picture label is bright PC1 VIDEO2 Sub picture label is bright PC1 VIDEO2 SELECT A B A B Input modes switching is possible Main picture label is changed Sub picture label is changed C VIDEO2 VIDEO1 B A PC1 VIDEO2 D Picture is changed Press to move the sub picture. Each time the location of the sub picture will be moved. Notes: · This button is effective only in the picture in picture. [. . . ] This is done to reduce after-image on the screen and the shortening of the screen's service life: It is normal and not indicative of malfunctioning. The unit digitally processes the various signals in order to reproduce esthetically pleasing images. As such, it sometimes takes a few moments for the picture to appear when the power has been turned on, when the input has been switched or when the images for the main picture and sub picture on the two screens are swapped. Due to the characteristics of the system used to drive the panel, the edges may appear to flicker in the fast-moving parts of the images: This is normal and not indicative of malfunctioning. [. . . ]