User manual PANASONIC TH-50PV700F

[. . . ] Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households) This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, please take these products to designated collection points, where they will be accepted on a free of charge basis. Alternatively, in some countries you may be able to return your products to your local retailer upon the purchase of an equivalent new product. Disposing of this product correctly will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. [. . . ] If "Skip" is selected, you cannot select the mode. · User input Select "User input" select access PC Setup V-pos Adjusts vertical position You can name each input terminals freely. Set characters User input Store select RETURN Clock Phase · · Eliminates flicker and distortion Adjust after Clock adjustment · Set to the minimum level if noise occurs Name ABCDE UVWXY abcde uvwxy FGHI Z 01 fghi z()+ J 2 j K 3 k . LMNOPQRS 456789!: lmnopqrs *_ T # t set Sync Chooses another synchronous signal if the image is distorted (H & V / On G) H & V : by the horizontal and vertical signals from your PC On G : by the green signal from your PC (if available) (maximum: ten characters) 26 · Other items p. 21 27 Viewing from card (Photos) The still images recorded by the digital camera will be displayed. 1 2 INPUT OPTION SD CARD EXIT Insert the SD Card · Warning message for output signal is displayed. · SD Card For details on SD Cards (p. 38) To open Blue LED To insert To remove Enter SD mode (Photo View Mode) Open the cover Label surface Push until a click is heard Press the centre of the card · Select the photo to be viewed Error display (images that could not be loaded, etc. ) Note Blue LED lights while SD Card is inserted if set "SD Card LED" to "On" in Setup Menu (p. 21). RETURN 3 Selected photo Slide show · Start Slide show (operate in step select or ) Start Slide show red Viewing from card (Photos) Select the photo for the first view Photo View Mode 1/17 Filename 100-0001 Date 10/23/2006 Pixel 1600 x 1200 · To pause 100-0001 100-0002 100-0003 100-0004 Slide show 100-0005 100-0006 100-0007 100-0008 100-0009 100-0010 100-0011 100-0012 view Reading Select EXIT Select RETURN · OPTION For details, see p. 29 red Slide show settings (operate in step Display the menu Select "Viewing Setup" Main Menu Picture Viewing Setup or ) Select the functions and set access Viewing Setup View Slide show set 5 seconds Off Selected photo information is displayed (Thumbnail screen) 4 To return to RETURN Operation guide View To display the operation guide View Rotate EXIT Select List Rotate Slide show or To previous photo Rotate 90° (anti-clockwise) To next photo · Menu Item Interval Repeat select Interval Repeat select "Picture Menu" (p. 20) Adjustments / Configurations (alternatives) Select slide show interval (5 / 10 / 15 / 30 / 60 / 90 / 120 seconds) Slide show repeat (Off / On) Viewing Setup Advanced Rotate 90° (clockwise) thumbnail screen Displayed one at a time On screen messages Message Is SD Card in? return ToEXIT to TV SD CARD or · · Caution During the operation, no signals are output from the monitor output terminals. "Date" shows the date on which the recording was made by the digital camera. It shows "**/**/****" when recordings are made without date signal. Meaning / Action · · · · Insert a SD card. 28 · · · · · · Cautions in handling SD Card Do not remove the card while the TV is accessing data (this can damage card or TV). Do not touch the pins on the back of the card. Do not subject the card to a high pressure or impact. Insert the card in the correct direction (otherwise, card may be damaged). Electrical interference, static electricity, or erroneous operation may damage the data or card. Back up the recorded data at regular intervals in case of deteriorated or damaged data or erratic operation of the TV. (Panasonic is not liable for any deterioration or damage of recorded data. ) No valid file to play The card has no data. Cannot read file The file is broken or unreadable. (For the applicable formats and data, see p. 38. ) 29 Q-Link Functions Q-Link connects the TV and VCR / DVD recorder, enables easy recording and playback. HDMI Functions HDMI (high-definition multimedia interface) allows you to enjoy high-definition digital images and highquality sound by connecting the TV and the equipment. HDMI-compatible equipment (1) with an HDMI or DVI output terminal, such as a set top box or a DVD player, can be connected to the HDMI terminal using an HDMI compliant (fully wired) cable. About connections, see "External Equipment" (p. 34). Condition · · · · · Use the VCR / DVD recorder with the following logos: "Q-Link", "NEXTVIEWLINK", "DATA LOGIC", "Easy Link", "Megalogic", or "SMARTLINK" Connect the equipment to this TV's AV2 or AV3 terminal via a "fully-wired" SCART cable. 34) Q-Link terminal setup in Setup menu (Q-Link, AV2 / AV3 out). 22) When first using this TV, see "Auto Setup". [. . . ] This is not a malfunction. · Using AV button please confirm your selection is S-Video I. e. 14). Pictures from external equipment are unusual when the equipment is connected via HDMI Is the HDMI cable connected properly?34) Turn Off the TV and equipment, then turn them On again. Check an input signal from the equipment. [. . . ]