User manual PANASONIC TH-60PF50E

[. . . ] Visit our Panasonic Web Site http://panasonic. net ii CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: To reduce the risk of electric shock, do not remove cover or back. Refer servicing to qualified service personnel. The lightning flash with arrow-head within a triangle is intended to tell the user that parts inside the product are a risk of electric shock to persons. The exclamation point within a triangle is intended to tell the user that important operating and servicing instructions are in the papers with the appliance. WARNING : To prevent damage which may result in fire or shock hazard, do not expose this apparatus to rain or moisture. [. . . ] · Ensure that "3D Picture Display" in "3D Settings" is set to "3D". (see page 35) · Some 3D image signals may not be automatically recognized as 3D images. Set "3D Picture Format" in "3D Settings" to match the picture format. (see page 35) · Check that there are no obstacles between the infrared sensors on the display and the 3D Eyewear. If the 3D Eyewear stops receiving the infrared signal for about 5 minutes, the 3D Eyewear will be turned off automatically. · Check the available area to use the 3D Eyewear. · Depending on the person, the 3D images may be difficult to see, or cannot be seen, especially in users that have a different level of eyesight between the left and right eyes. Take the necessary steps (wearing glasses etc. ) to correct your eyesight before use. · Check that there are no obstacles between the infrared sensors on the display and the 3D Eyewear or that the 3D Eyewear is placed inside the coverage area. If the 3D Eyewear stops receiving the infrared signal for about 5 minutes, the 3D Eyewear will be turned off automatically. · Check the setting of "3D Picture Sequence". In such case, switch to a bright image with borders and other objects are clearly shown, and then try auto setup again. · Depending on the signal, out of alignment may occur after Auto Setup. Carry out fine tuning for the position/size as required. · If Auto Setup cannot set properly for vertical frequency 60Hz XGA signal (1024×768@60Hz, 1280×768@60Hz, and 1366×768@60Hz), pre-selecting the individual signal in "XGA Mode" (see page 36) may results in correct Auto Setup. · Auto Setup does not work well when a signal such as additional information is superimposed out of valid image period or intervals between synchronizing and image signals are short, or for image signal with tri-level synchronizing signal added. · If Auto Setup cannot adjust correctly, select "Normalise" once and press OK button, then adjust Pos. /Size H-Pos Adjust the horizontal position. V-Pos Adjust the vertical position. H-Size Adjust the horizontal size. V-Size Adjust the vertical size. Dot Clock (During RGB and PC input signal) Periodic striped pattern interference (noise) may occur when a striped pattern is displayed. If this happens, adjust so that any such noise is minimized. (During RGB and PC input signal) Eliminate the flickering and distortion. Clock Phase Over scan Turn image over scan On/Off. Configurable signals are as follows: 525i, 525p, 625i, 625p, 750/60p, 750/50p, 1125 (1080) / 50i · 60i · 24sF · 24p · 25p · 30p · 50p · 60p, 1250 (1080) / 50i (RGB, DVI, SDI, HDMI) On Off Notes: · When "Off" is set, "H-Size" and "V-Size" cannot be adjusted. [. . . ] 4: The input signal is recognized as 1, 125 (1, 080) / 60p. 5: When inputted 525p signal to the PC IN terminal, it is recognized as VGA 60Hz signal. 6: Based on SMPTE 292M and 372M standards. These signals can be received when the Dual Link HD-SDI Terminal Note: Signals without above specification may not be displayed properly. 7: For 1 system Board (TY-FB11DHD) is installed. 47 Shipping condition This function allows you to reset the unit to the factory setting. 1 2 Setup Press to display the Setup menu. [. . . ]