User manual PANASONIC TH-61PHW6

[. . . ] ® PLASMA DISPLAY High Definition Plasma Display Operating Instructions + -- INPUT VOL BY R - STAND ON G POWER Model No. TH-61PHW6 For assistance in the USA, please call : 1-888-VIEW-PTV(843-9788) or e-mail us at : consumerproducts@panasonic. com or visit us at www. panasonic. com (U. S. A. ) Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference. English TQBC0644 WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: To reduce the risk of electric shock, do not remove cover or back. Refer servicing to qualified service personnel. The lightning flash with arrow-head within a triangle is intended to tell the user that parts inside the product constitute a risk of electric shock to persons. [. . . ] Batteries should always be replaced as a pair. Always use new batteries when replacing the old set. Do not combine a used battery with a new one. Do not mix battery types (example: "Zinc Carbon" with "Alkaline"). Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries. Battery replacement is necessary when the remote control acts sporadically or stops operating the Plasma Display. 9 Basic Controls R - STANDBY G POWER ON TH-61PHW6 INPUT -- VOL + Main POWER ON/OFF Switch Power Indicator The Power Indicator will light. POWER-OFF Indicator not illuminated (The unit will still consume some power as long as the power cord is inserted into the wall outlet. ) STAND-BY . . . . . Red POWER-ON. . . . . Green INPUT button (VIDEO(S VIDEO), COMPONENT/RGB, PC Mode Selection) Press the "INPUT" button to select VIDEO (S VIDEO), COMPONENT/RGB, PC input signal modes sequentially. (see page 19) · · · VOLUME Adjustment Press the Volume Up "+" or Down "­" button to increase or decrease the sound volume level. STAND-BY(ON/OFF) button The Plasma Display must first be plugged into the wall outlet and turned on at the power switch (see page 18). Press this button to turn the Plasma Display ON, from STANDBY mode. Press it again to turn the High Definition Plasma Display OFF to STAND-BY mode. STATUS button Press the "STATUS" button to display the current system status. VIDEO NORMAL SURROUND button (see page 28) INPUT button (VIDEO(S VIDEO), COMPONENT/ RGB, PC Mode Selection) Press to select VIDEO(S VIDEO), COMPONENT / RGB, PC input signal modes sequentially. (see page 19) INPUT 1 2 Sound mute On/Off (see page 27) VOLUME Adjustment Press the Volume Up "+" or Down "­" button to increase or decrease the sound volume level. SURROUND OFF TIMER 90 3 VOL 1 VIDEO(S VIDEO), COMPONENT / RGB, PC mode 2 ASPECT mode (see page 23) 3 OFF TIMER The off timer indicator is displayed only when the off timer has been set. N button (see page 21, 26, 27, 29) N R R button (see page 21) ACTION button Press to make selections POSITION buttons SET UP button (see page 33) SOUND button (see page 27) ASPECT PICTURE SOUND SET UP PICTURE button (see page 29) PICTURE POS. /SIZE PICTURE POS. /SIZE button (see page 25) PC OFF TIMER ASPECT button Press to adjust the aspect. (see page 23) PC button Press the "PC" mode selection button to select the PC mode. OFF TIMER button This button is used to switch The Plasma Display can be preset to switch to stand-by after a fixed period. setting changes to 30 minutes, 60 minutes, 90 minutes and 0 minutes (off timer cancelled) each time the button is pressed. 60 90 When three minutes remain, "OFF TIMER 3" will flash. 30 The off timer is cancelled if a power interruption occurs. 0 10 Connections / Cable fixing band SPEAKER Terminals (R) SPEAKER Terminals (L) Connect power plug to the socket of the main body. Fix the right clamper. How to fix: How to release: Fix by pushing in till a clicking sound is heard. Pull up while drawing the knob. ­ Cable fixing bands Secure any excess cables with bands, as required. Pass the attached cable fixing band through the clip as shown in the figure. [. . . ] If you would like to view 4:3 images in "Just" format, set to "JUST". 34 SET UP for Input Signals SYNC Select SIGNAL from the "SET UP" menu during RGB or PC input signal mode. Press to adjust. SET UP COMPONENT/RGB-IN SELECT RGB SIGNAL SCREENSAVER ENGLISH (US) OSD LANGUAGE Press SIGNAL SYNC R (ACTION) button [ RGB ] H&V Press to exit from adjust mode. SIGNAL SYNC H-FREQ. V-FREQ. 31. 5 kHz 60. 0 Hz [ PC ] H&V H-FREQ. V-FREQ. 31. 5 kHz 60. 0 Hz Setting RGB sync signal Confirm that the input is set to RGB INPUT (this setting is valid only for RGB INPUT). [. . . ]