User manual PANASONIC TH-65LFB70U

[. . . ] The exclamation point within a triangle is intended to tell the user that important operating and servicing instructions are in the papers with the appliance. WARNING: To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or moisture. Do not place containers with water (flower vase, cups, cosmetics, etc. ) above the set. (including on shelves above, etc. ) WARNING: 1) To prevent electric shock, do not remove cover. Refer servicing to qualified service personnel. [. . . ] TY-ST61PHW6 · Wall-hanging bracket (Vertical) . . . . . . . TY-WK61PV1 Always be sure to ask a qualified technician to carry out set-up. When using the Plasma Display Do not bring your hands, face or objects close to the ventilation holes of the Plasma Display. The top of the Plasma Display is usually very hot due to the high temperature of exhaust air being released through the ventilation holes. Burns or personal injuries can happen if any body parts are brought too close. Placing any object near the top of the display could also result in heat damages to the object as well as to the Display if its ventilation holes are blocked. · Be sure to disconnect all cables before moving the Plasma Display. Moving the Display with its cables attached might damage the cables which, in turn, can cause fire or electric shock. · · · Disconnect the power plug from the wall outlet as a safety precaution before carrying out any cleaning. Electric shocks can result if this is not done. /SIZE ASPECT PC OFF TIMER PLASMA DISPLAY Warranty Fixing bands TMME203× 2 AC cord Optional Accessories · Pedestal · Wall hanging bracket TY-WK61PV1 TY-ST61PHW6 For assembling Full instructions are supplied with each of the optional accessories for use with this Plasma Display. 8 Remote Control Batteries Requires two AA batteries. Install the batteries as shown in the battery compartment. (Polarity + or ­ must match the markings in the compartment. ) 3. Replace the cover and slide in reverse until the lock snaps. Two "AA" size Helpful Hint: For frequent remote control users, replace old batteries with Alkaline batteries for longer life. Precaution on battery use Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter. To secure cables connected to Terminals, wrap the cable fixing band around them then pass the pointed end through the locking block, as shown in the figure. 1 To tighten: Pull 2 To loosen: Push the catch Pull AUDIO R AUDIO L VIDEO S VIDEO R AUDIO L VD HD PR/CR/R PB/CB/B Y/G AV IN COMPONENT/RGB IN PC IN SERIAL AV IN Terminals (see page 12, 13, 16) COMPONENT / RGB IN and Audio IN Terminals (see page 13, 14, 16) From EXIT monitor Terminal on Computer (see page 15, 16) From SERIAL Terminal on Computer (see page 17) 11 Connections Speakers connection Two sets of speaker connections are provided for attaching 6 ohm speakers to the display. Refer to the manufacturers installation manual for your speakers for the correct hook up procedure. 1 Speakers 2 1 2 AV Input Terminals connection Connect the signal source equipment (see page 14 to 17). (Example) When connecting an S VIDEO VCR (S VIDEO VCR) R Audio OUT Video OUT S Video OUT L S VIDEO 4 pin socket Luminance earth Chrominance earth 2×RCA audio cables AUDIO Audio input to L/R sockets S VIDEO Video input to S VIDEO socket Luminance in Chrominance in R AUDIO L VIDEO S VIDEO AV IN Note: Additional equipment and cables shown are not supplied with this set. 12 Connections AV Input connection VIDEO signal connection (VCR) R Audio OUT L Video OUT AUDIO-VIDEO Video input to RCA socket 3×RCA audio video cables Audio input to L/R sockets R AUDIO L VIDEO S VIDEO AV IN Note: Additional equipment and cables shown are not supplied with this set. COMPONENT / RGB Input connection Component signals (Y, PB, PR ) connection (DVD Player) Y Y, PB, PR PB PR 3×RCA video cables AUDIO 2×RCA audio cables L R R AUDIO L VD HD PR/CR/R PB/CB/B Y/G COMPONENT/RGB IN Notes: (1) Change the "COMPONENT / RGB-IN" setting in the "SET UP" menu to "COMPONENT". (see page 33) (2) Additional equipment and cables shown are not supplied with this set. 13 Connections COMPONENT / RGB Input connection RGB signal (R, G, B, HD, VD) connection RGB input to R, G, B, HD, VD sockets Example of input signal source HDTV-compatible VCR BNC-RCA adaptor plug 5×BNC RGB cables RGB camera R AUDIO L VD HD PR/CR/R PB/CB/B Y/G COMPONENT/RGB IN AUDIO 2×RCA audio cables Audio input to L/R sockets Computer VD HD R B G Notes: (1) Change the "COMPONENT / RGB-IN" setting in the "SET UP" menu to "RGB". (see page 33) (2) Additional equipment, cables and adaptor plugs shown are not supplied with this set. 14 Connections PC Input Terminals connection COMPUTER AUDIO PC IN R - STANDBY G POWER ON TH-65LFB70U INPUT ­ VOL + Conversion adapter (if necessary) SVGA PC cable (with Ferrite cores) D-sub 15p Audio Stereo plug Connect a cable that matches the audio output terminal on the computer. Notes: (1) Computer signals which can be input are those with a horizontal scanning frequency of 15. 5 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1, 200 lines. ) (2) The display resolution is a maximum of 1, 024 × 768 dots when the aspect mode is set to "NORMAL", and 1, 366 × 768 dots when the aspect mode is set to "FULL". If the display resolution exceeds these maximums, it may not be possible to show fine detail with sufficient clarity. (3) The PC input terminals are DDC1/2B-compatible. If the computer being connected is not DDC1/2B-compatible, you will need to make setting changes to the computer at the time of connection. (4) Some PC models cannot be connected to the set. (5) There is no need to use an adapter for computers with DOS/V compatible D-sub 15P terminal. [. . . ] Press to select each function. SET UP COMPONENT/RGB-IN SELECT RGB SIGNAL SCREENSAVER ENGLISH (US) OSD LANGUAGE Press If the image becomes unstable: With the system set on Auto, under conditions of low level or noisy input signals the image may in rare cases become unstable. Should this occur, set the system to match the format of the input signal. Mode Color system SIGNAL (ACTION) button [ VIDEO ] ON AUTO NORMAL 3D Y/C FILTER (NTSC) COLOR SYSTEM Panasonic AUTO (4:3 ) Function Set the color system to match the input signal. If set to "AUTO", the color system is determined automatically. AUTO Panasonic AUTO (4:3) PAL SECAM M NTSC NTSC Set to "NORMAL" to view 4:3 images in an unchanged format when Panasonic AUTO is selected. [. . . ]