User manual PANASONIC TH-65PB1U

[. . . ] Visit our Panasonic Web Site http://panasonic. net ii CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: To reduce the risk of electric shock, do not remove cover or back. Refer servicing to qualified service personnel. The lightning flash with arrow-head within a triangle is intended to tell the user that parts inside the product are a risk of electric shock to persons. The exclamation point within a triangle is intended to tell the user that important operating and servicing instructions are in the papers with the appliance. WARNING : To prevent damage which may result in fire or shock hazard, do not expose this apparatus to rain or moisture. [. . . ] (see page 25, 28) 3 Select the item. Normalise ENTER/ Picture Mode Contrast Brightness Sharpness White balance Advanced settings 25 0 5 Monitor Press. Select. Warm Select (Example: Picture menu) ENTER/ 4 Set. Set. Adjust Press MENU Press several times. to return to the previous menu. Menu display list Picture menu Normalise Picture Mode Contrast Brightness Colour Hue Sharpness White balance Advanced settings 25 0 6 0 5 Normal External scaler mode Power save PC Power management Memory save Memory load Memory edit Auto power off OSD design OSD position OSD Language Normal Setup menu 3D Settings Signal Screensaver Extended life settings Input label Network Setup Component/RGB-in select RGB Off Off Off Off Type1 Upper left English (UK) Pos. /Size menu Normalise Auto Setup H-Pos H-Size V-Pos V-Size Dot Clock Clock Phase Clamp Position 1:1 Pixel Mode Under scan 0 0 0 0 0 0 0 Off Off Sound menu Normalise Balance Volume 0 1 see page 40 see page 25-27 see page 28-39 see page 41-52 24 Adjusting Pos. /Size Sound 2 access select 1 3 Select the item and set. Normalise Auto Setup H-Pos H-Size V-Pos V-Size Dot Clock Clock Phase Clamp Position 1:1 Pixel Mode Under scan 0 0 0 0 0 0 0 Off Off 2 1 adjust select Note: Unadjustable items are grayed out. Adjustable items differ depending on the input signal and the display mode. 4 Exit the menu. To display a menu for adjustment of the Pos. /Size menu on the bottom of the screen H-Pos 0 2 1 adjust or select select the menu To hide the menu or Notes: · Adjustment details are memorized separately for different input signal formats (Adjustments for component signals are memorized for 525 (480) / 60i · 60p, 625 (575) / 50i · 50p, 1125 (1080) / 60i · 50i · 60p · 50p · 24p · 25p · 30p · 24sF, 1250 (1080) / 50i, 750 (720) / 60p · 50p each, and RGB/PC/Digital signals are memorized for each frequency. ) · If a "Cue" or "Rew" signal from a VCR or DVD player is received, the picture position will shift up or down. This picture position movement cannot be controlled by the Picture Pos. /Size function. Helpful Hint ( Normalise Normalization) While the Pos. /Size display is active, if the OK button is pressed during "Normalise", then all adjustment values are returned to the factory settings. 25 Adjusting Pos. /Size Auto Setup H-Pos/V-Pos, H-Size/V-Size, Dot Clock and Clock Phase are automatically adjusted when the RGB or PC signal is received. This setting is enabled under the following conditions: · When "Component/RGB-in Select" or "YUV/RGB-in select" in the "Setup" menu (see page 41) is set to "RGB", this setting is enabled. (For 2k1k signals) Off On (Left) On (Center) On (Right) Note: 2k1k signals can only be received when the Dual Link HD-SDI Terminal Board (TY-FB11DHD) is installed. Under scan Adjusts the image display size on screen. Off: Sets the normal image display size on screen. On: Sets the image display size approximately 95 % of the normal image display. Off Notes: On · "Under scan" can be modified when "Studio mode" in the Options menu is "On". When "Studio mode" is "Off", this setting is "Off" and cannot be changed. (see page 53) · This setting is valid only when the input signals are as follows; 525i, 525p, 625i, 625p, 750/60p, 750/50p, 1125/60i, 1125/50i, 1125/24sF, 1125/25p, 1125/24p, 1125/30p, 1125/60p, 1125/50p, 1250/50i (RGB, DVI, SDI, HDMI) · When "Under scan" is set to "On", "H-Pos" and "V-Pos" in "Pos. · Refer to each board's operating instruction for DVI, SDI's corresponding signals. 27 Picture Adjustments 1 Display the menu screen. 2 Select "Picture". Picture Setup Pos. /Size Sound 2 access select 1 3 Select the item and set. Normalise Picture Mode Contrast Brightness Colour Hue Sharpness White balance Advanced settings 25 0 6 0 5 Normal Normal 2 1 adjust select Note: Menu that cannot be adjusted is grayout. Adjustable menu changes depending on signal, input and menu setting. 4 Exit the menu. To display a menu for adjustment of the Picture menu on the bottom of the screen, adjust or select select Contrast 25 2 1 To display a menu for Advanced settings adjustment, press PICTURE button again. Black extension 0 To hide the menu or Helpful Hint ( Normalise Normalization) While the "Picture" menu is displayed, if the OK button is pressed during "Normalise", then all adjustment values are returned to the factory settings. 28 Picture Adjustments Picture Mode You can switch to the optimal picture mode for the video source and viewing environment. Normal Monitor Dynamic Cinema Normal: Cinema: For viewing in standard (evening lighting) environments. This menu selects the normal levels of Brightness and Monitor: Contrast. For use when creating broadcast or movie content. [. . . ] 4 Press the or button to select "YES". 6 Press the or button to select "YES". 7 Press the ENTER button and wait for 10 sec. Executing this function restores all settings and adjustment values in the following menus to the factoryset default values, as shipped. [. . . ]