User manual PANASONIC TH-65PF9EK

[. . . ] Operating Instructions High Definition Plasma Display Model No. TH-65PF9EK The illustration shown is an image. Please read these instructions before operating your set and retain them for future reference. English Dear Panasonic Customer Welcome to the Panasonic family of customers. We hope that you will have many years of enjoyment from your new Plasma Display. To obtain maximum benefit from your set, please read these Instructions before making any adjustments, and retain them for future reference. Retain your purchase receipt also, and note down the model number and serial number of your set in the space provided on the rear cover of these instructions. [. . . ] When exiting the mode, the screen will return to a former adjustment. During "Component", "RGB" and "PC" input signal. Pos. /Size Normalise Auto Setup Normal H-Pos H-Size V-Pos V-Size Dot Clock Clock Phase 1:1 Pixel Mode 0 0 0 0 0 0 Off Helpful Hint ( / Normalise Normalisation) While the Pos. / Size display is active, if either the N button on the remote control is pressed at any time or the ACTION ( ) button is pressed during "Normalise", then all adjustment values are returned to the factory settings. 19 Adjusting Pos. /Size Auto Setup Automatically adjust H-Pos / V-Pos / Clock Phase / Dot Clock and set H-Size / V-Size the standard value when RGB signal is input. Notes: · If the dot clock frequency is 162 MHz or higher, Dot Clock cannot be made. · If the image is that the edge is hardly figured out or shadowy, that cannot be adjusted automatically. In such case, press Auto Setup again after changing the image to the clearer one. · When DVI-D is input, Clock Phase cannot be adjusted automatically. /Size and press the ACTION ( ) button when appropriate adjustment cannot be made. Adjust the horizontal position. H-Pos H-Size Adjust the horizontal size. V-Pos Adjust the vertical position. V-Size Adjust the vertical size. Dot Clock (During "Component", "RGB" and "PC" input signal) Periodic striped pattern interference (noise) may occur when a striped pattern is displayed. If this happens, adjust so that any such noise is minimized. (During "Component", "RGB" and "PC" input signal) Eliminate the flickering and distortion. Adjusts the display size when 1125i, 1125p or 1250i signal is input. Notes: · Select On when you would like to replay 1920 × 1080 input signal. · Applicable input signal; 1125 / 50i · 60i · 24sF · 24p · 25p · 30p · 50p · 60p , 1250 / 50i · Select Off when flickering is shown around the image. · H-Size, V-Size and Dot Clock cannot be adjusted when On is selected. Clock Phase 1:1 Pixel Mode Off On Helpful Hint ( / Normalise Normalisation) While the Pos. /Size display is active, if either the N button on the remote control is pressed at any time or the ACTION ( ) button is pressed during "Normalise", then all adjustment values are returned to the factory settings. 20 MULTI PIP Press repeatedly. Each time pressing this button main picture and sub picture will be displayed as follows below. [Picture and Picture] Main picture Sub picture [Picture out Picture] Main picture Sub picture [Picture in Picture] Main picture Sub picture Normal Viewing MULTI PIP MULTI PIP MULTI PIP A B SWAP A SWAP B A B SWAP Press to swap main picture and sub picture. B A B A B A Press to select the input mode. Under main Picture and sub picture display, select the picture which you would like to change input modes. Notes: · The sub picture sound is heard while a sub picture operation is underway. · The sub picture operation automatically returns to the main picture operation if a sub picture operation has not been performed for about 5 seconds or if any of the remote control buttons is pressed (except button). Press to change input signal. [Example] Main picture label is bright PC1 VIDEO2 Sub picture label is bright PC1 VIDEO2 SELECT A B A B Input modes switching is possible Main picture label is changed Sub picture label is changed C VIDEO2 VIDEO1 B A PC1 VIDEO2 D Picture is changed Press to move the sub picture. [. . . ] The plasma display panel is manufactured using an extremely high level of precision technology, however, sometimes some parts of the screen may be missing picture elements or have luminous spots. Do not allow a still picture to be displayed for an extended period, as this can cause a permanent after-image to remain on the Plasma Display. Examples of still pictures include logos, video games, computer images, teletext and images displayed in 4:3 mode. Note: The permanent after-image on the Plasma Display resulting from fixed image use is not an operating defect and as such is not covered by the Warranty. [. . . ]