User manual PANASONIC TH-85VX200U

[. . . ] Model No. TH-103VX200U TH-85VX200U Operating Instructions High Definition Plasma Display English Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: To reduce the risk of electric shock, do not remove cover or back. Refer servicing to qualified service personnel. The lightning flash with arrow-head within a triangle is intended to tell the user that parts inside the product are a risk of electric shock to persons. [. . . ] · If AUTO SETUP cannot set properly for vertical frequency 60Hz XGA signal (1024×768@60Hz, 1280×768@60Hz, and 1366×768@60Hz), pre-selecting the individual signal in "XGA MODE" (see page 48) may results in correct AUTO SETUP. · AUTO SETUP does not work well when a signal such as additional information is superimposed out of valid image period or intervals between synchronizing and image signals are short, or for image signal with tri-level synchronizing signal added. · If AUTO SETUP cannot adjust correctly, select "NORMALIZE" once and press OK button then adjust POS. /SIZE manually. H-POS Adjust the horizontal position. V-POS Adjust the vertical position. H-SIZE Adjust the horizontal size. V-SIZE Adjust the vertical size. DOT CLOCK (During Component, RGB and PC input signal) Periodic striped pattern interference (noise) may occur when a striped pattern is displayed. If this happens, adjust so that any such noise is minimized. CLOCK PHASE (During Component, RGB and PC input signal) Eliminate the flickering and distortion. 29 Adjusting POS. /SIZE OVER SCAN Turn image over scan ON/OFF. Configurable signals are as follows: 525i, 525p, 625i, 625p, 750/60p, 750/50p (Component Video, RGB, DVI, SDI, HDMI) ON OFF Notes: · When "OFF" is set, "H-SIZE" and "V-SIZE" cannot be adjusted. · When the "UNDER SCAN" is set to "ON", this setting will be invalid. CLAMP POSITION (During Component and RGB input signal) Adjusts the clamp position when black parts of the image have no detail due to underexposure or are tinged with green. Optimum value for Clamp Position adjustment When black parts have no detail due to underexposure (blackout) Value that causes least blackout is the optimum. When black parts are tinged with green Value that cancels the greenishness without causing blackout is the optimum. Notes: · Select ON when you would like to replay 1920 × 1080 input signal. · Applicable input signal; 1125 (1080) / 50i · 60i · 24sF · 24p · 25p · 30p · 50p · 60p, 1250 (1080) / 50i · Select OFF when flickering is shown around the image. · H-SIZE and V-SIZE cannot be adjusted when ON is selected. 1:1 PIXEL MODE Adjusts the display size when 1125i, 1125p or 1250i signal is input. 1:1 PIXEL MODE (2k1k) (For 2k1k signals) OFF ON When the input signal is a 2k1k signal (2048×1080 / 24p, 2048×1080 / 24sF), the display size is adjusted as follows. OFF ON (LEFT) ON (CENTER) ON (RIGHT) Note: 2k1k signals can only be received when the Dual Link HD-SDI Terminal Board (TY-FB11DHD) is installed. UNDER SCAN Adjusts the image display size on screen. OFF: Sets the normal image display size on screen. ON: Sets the image display size approximately 95 % of the normal image display. OFF Notes: ON · "UNDER SCAN" can be modified when "Studio mode" in the OPTIONS menu is "On". When "Studio mode" is "Off", this setting is "OFF" and cannot be changed. (see page 56) · This setting is valid only when the input signals are as follows; 525i, 525p, 625i, 625p, 750/60p, 750/50p, 1125/60i, 1125/50i, 1125/24sF, 1125/25p, 1125/24p, 1125/30p, 1125/60p, 1125/50p, 1250/50i (Component Video, RGB, DVI, SDI, HDMI) · When "UNDER SCAN" is set to "ON", "H-POS" and "V-POS" in "POS. · Refer to each board's operating instruction for DVI, SDI's corresponding signals. 30 PICTURE Adjustments 1 Display the menu screen. 2 Select "PICTURE". PICTURE SET UP POS. /SIZE SOUND 2 access select 1 3 Select the item and set. NORMALIZE PICTURE MENU PICTURE BRIGHTNESS COLOR TINT SHARPNESS COLOR TEMP ADVANCED SETTINGS 25 0 6 0 5 NORMAL STANDARD 2 1 adjust select Note: Menu that cannot be adjusted is grayout. Adjustable menu changes depending on signal, input and menu setting. 4 Exit the menu. To display a menu for adjustment of the PICTURE menu on the bottom of the screen, adjust or select select PICTURE 25 2 1 To display a menu for ADVANCED SETTINGS adjustment, press PICTURE button again. BLACK EXTENSION 0 To hide the menu or Helpful Hint ( NORMALIZE Normalization) While the "PICTURE" menu is displayed, if the OK button is pressed during "NORMALIZE", then all adjustment values are returned to the factory settings. 31 PICTURE Adjustments PICTURE MENU You can switch to the optimal picture mode for the video source and viewing environment. STANDARD MONITOR DYNAMIC CINEMA STANDARD: CINEMA: For viewing in standard (evening lighting) environments. This menu selects the normal levels of BRIGHTNESS MONITOR: and PICTURE. For use when creating broadcast or movie content. [. . . ] YES NO 1 2 select set Note: Press to return to SET UP menu when confirmation screen is displayed. [from the unit] 1 Press the MENU button till the SET UP menu is displayed. 2 Press the or button to select "OSD LANGUAGE". 3 Press the ENTER button for more than 5 seconds. [. . . ]