User manual PANASONIC TH-R42PY8SR

[. . . ] Visit our Panasonic Web Site http://panasonic. net Table of Contents Important Safety Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Accessories Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 4:3 16 : 9 [from the unit] INPUT MENU VOL ENTER/ [During MULTI PIP Operations] · Picture and Picture, Picture in Picture : · Others : Aspect switching is not possible. Notes: · For PC signal input, the mode switches between "4:3", "Zoom" and "16:9" only. · For a 1125 (1080) / 60i · 50i · 24p · 25p · 30p · 24sF, 1250 (1080) / 50i, 750 (720) / 60p · 50p signal input, the mode is set to "16:9" mode, and switching is not possible. · Panasonic Auto can be selected only during Video signal input. · The aspect mode is memorized separately for each input terminal. Mode 4 4:3 Picture Explanation 4:3 will display a 4:3 picture at its standard 4:3 size. 4:3 3 4 16 Zoom Zoom mode magnifies the central section of the picture. 9 Zoom 3 4 16 16 : 9 16:9 will display the picture at its maximum size but with slight elongation. 9 16 : 9 3 4 16 Just Just 3 9 Just mode will display a 4:3 picture at its maximum size but with aspect correction applied to the center of the screen so that elongation is only apparent at the left and right edges of the screen. The size of the picture will depend on the original signal. The display will automatically become enlarged (depending on the picture source), allowing you to view the picture at its maximum size. Notes: · Panasonic Auto mode is designed to automatically adjust the aspect ratio to handle a mix of 16:9 and 4:3 program material. Certain 4:3 program material, such as stock market data screens, may occasionally cause the image size to change unexpectedly. When viewing such programs, it is recommended that the ASPECT be set to 4:3. · If adjusting the Picture V-Pos/V-Size in Panasonic Auto with 16:9 mode, the adjustment is not memorized. When exiting the mode, the screen will return to a former adjustment. · Due to the small dimensions of the sub pictures, these sub pictures cannot be shown in detail. · Computer screen picture is displayed in a simplified format, and it may not be possible to discern details on them satisfactorily. · Following combinations of two analog signals cannot be displayed simultaneously; Component - Component, Component - PC (RGB), PC (RGB) - Component, PC (RGB) - PC (RGB) 19 Advanced PIP 1 2 Press to display the Setup menu. Press to select "OSD Language". 3 4 Press and hold until the Options menu is displayed. Press to select Advanced PIP. Options Off-timer function Onscreen display Initial INPUT Initial VOL level Maximum VOL level INPUT lock Studio W/B Advanced PIP Display size 1/3 Enable On Off Off 0 Off 0 Off Off Off Off 5 Press to adjust the menu. Off : Sets normal two screen display mode (see page 19). One screen Advanced PIP 6 7 Note: To use , , Press to exit from Options menu. Sub screen Main screen (When Advanced PIP is On) Press repeatedly. Each time pressing this button main picture and sub picture will be displayed as above. , buttons for the screen operations, follow the procedures in the previous page. Notes: · Advanced PIP corresponding signal Sub screen NTSC, PAL, SECAM (tuner, video) 525i, 525p, 625i, 625p, 750/60p, 750/50p, 1125/60i, 1125/50i, 1250/50i (Component Video, RGB, DVI, SDI, HDMI) Main screen 640x480@60Hz, 852x480@60Hz, 1024x768@60Hz, 1366x768@60Hz (RGB, DVI, HDMI) 1280x768@60Hz (DVI) · Sound output is from the picture which is selected in Audio Out (PIP) (See page 23). · In 2 screen display, the same input mode cannot be selected for the main picture and sub picture. · The main picture and sub picture are processed by different circuits, resulting in a slight difference in the clarity of the pictures. [. . . ] As such, it sometimes takes a few moments for the picture to appear when the power has been turned on, when the input has been switched or when the images for the main picture and sub picture on the two screens are swapped. Due to the characteristics of the system used to drive the panel, the edges may appear to flicker in the fast-moving parts of the images: This is normal and not indicative of malfunctioning. When viewing the side panels at the "High" or "Mid" setting, the brightness on both sides may change depending on the kind of program shown: This is normal and not indicative of malfunctioning. The plasma display panel is manufactured using an extremely high level of precision technology, however, sometimes some parts of the screen may be missing picture elements or have luminous spots. [. . . ]