User manual PANASONIC TOUGHBOOK CF18BDAZXMM

[. . . ] To activate a submenu press the [Enter] key. To return to a menu from a submenu, press the [Esc] key. To go to the Exit menu from any other menu, press the [Esc] key. POINT Selecting a field causes a help message about that field to be displayed on the right-hand side of the screen. POINT Pressing the Enter key with the highlight on a selection that is not a submenu or auto selection will cause a list of all options for that item to be displayed. Pressing the Enter key again will select the highlighted choice. Entering the BIOS Setup Utility To enter the BIOS Setup Utility do the following: 1. [. . . ] <Enabled> The pointing device is enabled. <Disabled> The pointing device is disabled. <Exclusive Enabled> The pointing device is enabled. However, the pointing device is disabled when an external PS/2 mouse is connected. F9 Setup Defaults F10 Save and Exit Keyboard/Mouse Features Numlock: Hot Plug: Quick Point Manual Setting: Pointing Device: Touch Panel: Quick Point: External PS/2 Mouse: [Auto] [Enabled] [Disabled] [Configuration 1] Enabled Enabled Disabled F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu v Figure 5. Keyboard/Mouse Features Submenu Table 5: Fields, Options and Defaults for the Keyboard/Mouse Features Submenu of the Advanced Menu Menu Field Numlock: Options · Auto · On · Off · Disabled · Enabled · Disabled · Enabled Default [Auto] Description Sets the NumLock function state when the computer completes booting. Hot Plug: [Enabled] Enables and disables the ability to plug a mouse or keyboard into the PS/2 port and have it immediately recognized and active. Enables and disables the ability to use Hot key to enable or disable the Quick Point. Quick Point Manual Setting: [Disabled] 12 Advanced Menu Table 5: Fields, Options and Defaults for the Keyboard/Mouse Features Submenu of the Advanced Menu Menu Field Pointing Device: Options · · · · Configuration 1 Configuration 2 Configuration 3 Configuration 4 Default [Configuration 1] Description Selects pointing device configurations. Configuration 1: Touch Panel: Enabled Quick Point: Enabled External PS/2 Mouse: Disabled Configuration 2: Touch Panel: Enabled Quick Point: Disabled External PS/2 Mouse: Enabled Configuration 3: Touch Panel: Disabled Quick Point: Enabled External PS/2 Mouse: Enabled Configuration 4: Touch Panel: Disabled Quick Point: Exclusive Enabled External PS/2 Mouse: Enabled 13 LifeBook B Series BIOS Video Features Submenu of the Advanced Menu The Video Features Submenu is for setting the display parameters. Main Advanced PhoenixBIOS Setup Utility Security Power Savings Exit Item Specific Help Video Features Display Compensation: [Internal Flat Panel] [Disabled] Select display terminal. F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu v F9 Setup Defaults F10 Save and Exit Figure 6. Video Features Submenu Table 6: Fields, Options and Defaults for the Video Features Submenu of the Advanced Menu Menu Field Display: Options · Internal Flat-Panel · External · Simultaneous · Disabled · Enabled Default [Internal Flat-Panel] Description Selects where the video signal will be routed. Compensation: [Disabled] Enables or disables compensation which controls spacing on the display. When enabled, displays with less than pixel resolution 1024 x 768 or 800 x 600 will still cover the entire screen. 14 Advanced Menu Internal Device Configurations Submenu of the Advanced Menu The Internal Device Configurations submenu allows the user to configure other internal devices. Main Advanced PhoenixBIOS Setup Utility Security Power Savings Exit Item Specific Help Internal Device Configurations Floppy Disk Controller: [Disabled] IDE Controller: [Enabled] LAN Controller: [Auto] [Disabled] Floppy disk drive is disabled. [Enabled] Floppy disk drive is enabled. F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu v F9 Setup Defaults F10 Save and Exit Figure 7. Then password entry is required to enter BIOS Setup. Table 12: Fields, Options and Defaults for the Security Menu Menu Field Supervisor Password is: User Password is: vv [Normal] [Enabled] F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu Figure 12. Security Menu v F9 Setup Defaults F10 Save and Exit Options ­-- Default Clear Description A display-only field. Set is displayed when the system supervisor password is set and Clear when it is not. Set is displayed when the general user password is set, and Clear when it is not. Sets, changes or cancels the Supervisor Password. The Supervisor Password may be up to seven characters long and must include only letters or numbers (no symbols). To cancel a password press the Enter key instead of entering characters in the Enter New Password field and in the Re-enter New Password field. When a Supervisor Password is set it must be used to access the BIOS setup utility. This field can only be accessed if the Supervisor Password is set. Sets, changes or cancels the User Password. The User Password may be up to seven characters long and must include only letters or numbers (no symbols). [. . . ] <+>/<Space> or <-> moves the device up or down. <Shift + 1> enables or disables a device. © © Main Advanced Boot Device Priority +Floppy Disk Drive +Hard Disk Drive F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu v F9 Setup Defaults F10 Save and Exit Figure 18. Boot Device Priority Submenu Table 18: Fields, Options and Defaults for the Boot Device Priority Submenu of the Boot Menu Menu Field Floppy Disk Drive Options ­-- Description The boot selections determine the order in which the BIOS searches for the operating system during a startup sequence. [. . . ]