User manual PANASONIC TU-IRD20

[. . . ] The exclamation point within a triangle is intended to tell the user that important operating and servicing instructions are in the papers with the appliance. WARNING: To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or moisture. To prevent electric shock, do not remove cover. Refer servicing to qualified service personnel. Important Safety Instructions Read these instructions All the safety and operating instructions shall be read before the appliance is operated. Keep these instructions The safety and operating instructions shall be retained for future reference. [. . . ] 60. 0 Hz CHANGE SELECT EXIT TO PICTURE POS. /SIZE adjust screen PICTURE POS. /SIZE NORMALIZE NORMAL H-POS H-SIZE V-POS V-SIZE CLOCK PHASE ADJUST EXIT SELECT TO SOUND adjust screen SOUND NORMALIZE AUDIO MENU BASS TREBLE BALACE SURROUND ADJUST EXIT NORMAL STANDARD 0 0 NORMAL SELECT STANDARD 0 0 0 ON SELECT see page 36 see page 30 see page 33 see page 52 19 Tuning channels (Automatic channel programming) Automatically searches and adds receivable channels in the installed area and / or CATV signals to the program. Channel tuning cannot be performed when the MAIN picture is not receiving a TV broadcast (tuning is not possible). 1 2 Press the MENU button to display the MENU screen and select SETUP. MENU ADJUST LANGUAGE SET UP CH PROGRAM CHANNELS Press to select PROGRAM CHANNELS. VOL LOCK CLOSED CAPTION VIDEO PAGE ACTION EXIT SELECT ACTION VOL CH Press to display the PROGRAM CHANNELS. 3 VOL CH Press to select MODE. Press to select TV or CABLE. PROGRAM CHANNELS MODE TV AUTO PROGRAM MANUAL PROGRAM CHANGE EXIT SELECT CABLE ACTION VOL CH 4 VOL CH AUTO PROGRAM Press to select AUTO PROGRAM. ACTION VOL Activate "AUTO PROGRAM"?YES EXIT NO CHANNEL CH Press to display the confirmation screen. Press to select YES. AUTO PROGRAM IN "AUTO PROGRAM" 5 VOL CH ACTION VOL CHANNEL 59 MENU STOP CH Press to run AUTO PROGRAM. Channels will automatically advance until all channels have been scanned. Channel numbers with a video signal present will turn blue which indicates stored in the Channel Scan Memory. 6 · · · Press to select YES. Notes: When buttons are pressed with AUTO PROGRAM running, this unit will return to normal viewing. (Channels searched up to this point are added. ) After AUTO PROGRAM is finished, the lowest channel number added will be received. When there are no receivable channels, channel 69 is displayed (channel 125 for cable TV). 20 Tuning channels (Manual channel programming) Use this setting when changing setting of receiving channels or changing the channel display. Turn this unit on and select the broadcast channel. Follow the steps on the previous page to display the PROGRAM CHANNEL screen. This PROGRAM CHANNEL screen can be displayed when the MAIN picture is a TV broadcast. 1 2 Press the MENU button to display the MENU screen and select SETUP. CH MENU ADJUST LANGUAGE SET UP Press to select PROGRAM CHANNELS. VOL PROGRAM CHANNELS LOCK CLOSED CAPTION VIDEO ACTION VOL CH Press to display the PROGRAM CHANNELS. Press to select TV or CABLE. PROGRAM CHANNELS MODE TV AUTO PROGRAM MANUAL PROGRAM CABLE 3 VOL CH ACTION VOL CH 4 VOL CH MANUAL PROGRAM Press to select MANUAL PROGRAM. ACTION VOL ENTER CHANNEL: DELETE EXIT 122 ADD CH SELECT (or number key) CH Press to display the MANUAL PROGRAM screen. Adding or deleting channels 5 VOL CH MANUAL PROGRAM Press to select channel ( or number keys ). ACTION VOL ENTER CHANNEL: DELETE EXIT 122 ADD CH SELECT (or number key) CH 6 VOL CH Press to add channels to memory ( blue ). Press to select channel. VOL ACTION CH Press to delete channels from memory ( yellow ). 7 8 Repeat steps 4 and 5 to continue adding or deleting channels. Note: When the remote control is unavailable, input modes can also be switched on front of this unit using the INPUT button. 3 26 Operate the connected equipment. Recall Recall (On-screen display) TV, VIDEO input mode LIGHT INFO/RECALL POWER ASPECT MUTE TV/VIDEO The channel number remains, but other information disappears after 10 seconds. Press this button again to delete channel number display. Full Information Channel number channel number or Video Input Selected multiplex sound ASPECT mode DVD AUX CBL CH R VC RC VR DB S DTV TV CH123 VOL MENU CH SURROUND NORMAL OFF TIMER CH123 ACTION VOL INFO/RECALL STEREO SAP MONO NORMAL PC EXIT VCR REC GUIDE REW STOP PLAY FF OFF TIMER 30 OFF TIMER status (See page 45) TV/VCR OPEN/CLOSE VCR/DBS CHANNEL PAUSE STILL The INFO/RECALL button switches the display in the following order. SLOW 1 4 7 R-TUNE 2 5 8 0 3 6 9 PROG Full Information Channel No display Press this button to display channel number, off-timer remaining time, screen modes, and other settings. PC input mode INFO/RECALL Press this button to display input signal, screen mode, and disappears after 3 seconds. Following screen is displayed in PC input mode. PC NORMAL PC Input selected ASPECT mode OFF TIMER 30 OFF TIMER status (See page 45) 27 Adjusting screen POSITION/SIZE (TV, VIDEO input mode) Adjusting screen 1 2 ASPECT Press to select the screen mode to adjust. LIGHT POWER MENU ASPECT Press to display the MENU. MUTE TV/VIDEO DVD AUX CBL CH R VC RC VR DB S DTV CH Press to select ADJUST menu. VOL TV MENU ADJUST SET UP VOL MENU CH SURROUND NORMAL OFF TIMER VOL ACTION PICTURE PICTURE ADJUST POSITION / SIZE AUDIO SOUND ADJUST AUDIO MODE ACTION VOL INFO/RECALL PC CH EXIT VCR REC GUIDE REW PAGE EXIT ACTION SELECT STOP PLAY FF TV/VCR OPEN/CLOSE VCR/DBS CHANNEL PAUSE STILL SLOW 3 VOL CH POSITION / SIZE NORMAL 1 4 7 R-TUNE 2 5 8 0 3 6 9 PROG Press to select POSITION/SIZE. ACTION VOL SIZE 1 POSITION NORMALIZE CH Press to display the POSITION/SIZE screen. Notes: This unit is equipped with various screen modes. If a screen mode with a different aspect as the broadcast program is selected, image will appear differently. Select the proper screen mode with this in mind. Be careful when using this unit for commercial purposes or for public use, such as in cafes and hotels, for shrinking and enlarging images by using screen mode switching function (zoom, etc. ) may violate copyright laws. Images displayed on a wide screen unit will be cut off or distorted at the edges, when viewing normal aspect images of 4:3 in ZOOM, JUST or FULL mode. Display in NORMAL mode to view the original image intended by the producer. For 1080i, 720p and 480p input images, screen position and size cannot be adjusted. [. . . ] · If the power does not turn on using the remote, check if this unit is turned on. Confirm that the Wide Plasma Display is connected to the rear · DISPLAY OUT terminal (D-SUB) of the tuner using the dedicated display cable. The tuner will not turn ON if connected using a different cable. 10 Remote control does not function. Image shakes Image is not clear Color patches or no color. [. . . ]