User manual PANASONIC TU-PTA500U

[. . . ] ® CONTROLLER / TUNER POWER R-STAND BY G-POWER ON INPUT 3 S-VIDEO VIDEO L-AUDIO-R MENU ACTION INPUT VOLUME CHANNEL Operating Instructions Model No. TU-PTA500U V ID S -V ID E O D IO 3 U T L- A U IN P O E -R CH VO ACT IO N IM P UT E LUM ANN EL MEN Y DB TAN ON R-S WER O G-P U PO WE R For assistance, please call : 1-888-VIEW-PTV (843-9788) or send e-mail to : consumerproducts@panasonic. com or visit us at www. panasonic. co. jp/global/ (U. S. A) (Puerto Rico) (Canada) For assistance, please call : 787-750-4300 For assistance, please call : 1-800-561-5505 or visit us at www. panasonic. co. jp/global/ Before connecting, operating or adjusting this product, please read these instructions completely. Save this manual for future reference. TQBC0216 WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: To reduce the risk of electric shock do not remove cover or back. Refer servicing to qualified service personnel. The lightning flash with arrow-head within a triangle is intended to tell the user that parts inside the product are a risk of electric shock to persons. [. . . ] (2) There may be a slight delay for the screen size to adjust. If a 480p or 720p or 1080i signal is input during component input signal mode, the controls will not operate. NORMAL will display a 4:3 picture at its standard 4:3 size. 9 For an elongated image 4 Image is expanded Changes in accordance with the Panasonic AUTO mode setting (see page 49) Panasonic AUTO For a 4:3 image 3 4 NORMAL NORMAL 3 4 JUST 16 3 9 JUST JUST mode will display a 4:3 picture at its maximum size but with aspect correction applied to the center of the screen so that elongation is only apparent at the left and right edges of the screen. The size of the picture will depend on the original signal. ZOOM mode magnifies the central section of the picture. 4 ZOOM 16 3 9 ZOOM 4 FULL 16 3 9 FULL will display the picture at its maximum size but with sight elongation. FULL Note: The screen size also changes if ID-1 is detected. 23 VHF, UHF and CATV POWER R-STAND BY G-POWER ON INPUT 3 S-VIDEO VIDEO L-AUDIO-R MENU ACTION INPUT VOLUME CHANNEL Operation can be done from this unit. Power switch · Channel buttons · Volume buttons 1 LIGHT POWER Press to turn this unit on (See page 15). POWER ASPECT MUTE TV/VIDEO DVD AUX CBL CH 2 3 VOL TV R VC RC VR DB S Press to operate this unit with the remote control. DTV TV CH Press to select the desired channel. ACTION VOL VOL MENU ACTION VOL INFO/RECALL CH SURROUND NORMAL OFF TIMER PC CH EXIT VCR REC GUIDE REW STOP PLAY FF 4 VOL CH Press to select the desired volume level. TV/VCR OPEN/CLOSE VCR/DBS CHANNEL PAUSE STILL SLOW ACTION VOL 1 4 7 R-TUNE 2 5 8 0 3 6 CH 9 PROG Notes: The channel number and volume level are set even after this unit is turned off. Power consumption and howling of sound can be reduced if the volume level is lowered. · · 24 Cable TV ANTENNA TERMINALS ON THE BACK OF THIS UNIT. INPUT 3 S-VIDEO VIDEO L-AUDIO-R POWER R-STAND BY G-POWER ON MENU ACTION INPUT VOLUME CHANNEL When the antenna cable is connected to the TV antenna terminal via a cable box or VCR, set the TV channel to CH3 or CH4 (see page 9). This does not apply when signal is input from VIDEO INPUT. To antenna Input Incoming Cable from Antenna or Cable TV System. ferrite sleeve OUTPUT INPUT CABLE BOX LIGHT POWER ASPECT MUTE TV/VIDEO Confirming Confirm that registration with cable TV and connection of equipment are completed. Turn the cable TV tuner and select the desired volume level. DVD AUX CBL CH R VC RC VR DB S DTV TV 1 2 CBL VOL MENU ACTION VOL INFO/RECALL POWER Press while pointing the remote control towards the cable TV tuner. Note: The remote control code number is set for Panasonic products. When peripheral equipment do not operate, reset code (See page 54). CH SURROUND NORMAL OFF TIMER PC EXIT VCR REC GUIDE REW STOP PLAY FF TV/VCR OPEN/CLOSE VCR/DBS CHANNEL PAUSE STILL SLOW 1 4 7 R-TUNE 2 5 8 0 3 6 9 PROG 3 Operate the cable TV tuner and select the desired volume level. 25 Selection input signal Confirming connection of the connector for desire selection signal. TV COMPONENT 1 COMPONENT 2 VCR ANT AUDIO OUT COMPONENT VIDEO INPUT PC-IN 1 1 INPUT DISPLAY OUT AUDIO R L PR PB Y 2 VIDEO 2 OUTPUT Laser Disk Player AUDIO R - L VIDEO S-VIDEO PC VIDEO 2 VIDEO 3 VIDEO 1 A video camera uses the Video Input 3 terminal on the front of this unit. DVD Player This equipment can also be connected to the rear terminals. See Connections for details. INPUT 3 S-VIDEO VIDEO L-AUDIO-R E CHANNEL Video camera Turning the power on and switching input modes LIGHT 1 2 POWER Turn this unit on. POWER ASPECT MUTE TV/VIDEO DVD R VC TV AUX CBL CH TV/VIDEO RC VR DB S DTV The input mode changes each time this button is pressed. INPUT TV VOL ACTION VOL Input modes can also be switched using the INPUT button on the unit. MENU ACTION INPUT VOLUME CHANNEL · When playing a video · When playing a DVD · When playing from a video camera PC VIDEO 1 COMPONENT 2 VIDEO 2 COMPONENT 1 VIDEO 3 No input mode is displayed for terminals with no equipment connected (Excluding PC). PC input can only be selected by using the INPUT button on the front of the tuner. PC input can also be selected by pressing the PC button on the remote. Note: When the remote control is unavailable, input modes can also be switched on front of this unit using the INPUT button. 3 26 Operate the connected equipment. Recall Recall (On-screen display) TV, VIDEO input mode LIGHT INFO/RECALL POWER ASPECT MUTE TV/VIDEO The channel number remains, but other information disappears after 10 seconds. Press this button again to delete channel number display. Full Information Channel number channel number or Video Input Selected multiplex sound ASPECT mode DVD AUX CBL CH R VC RC VR DB S DTV TV CH123 VOL MENU CH SURROUND NORMAL OFF TIMER CH123 ACTION VOL INFO/RECALL STEREO SAP MONO NORMAL PC EXIT VCR REC GUIDE REW STOP PLAY FF OFF TIMER 30 OFF TIMER status (See page 45) TV/VCR OPEN/CLOSE VCR/DBS CHANNEL PAUSE STILL The INFO/RECALL button switches the display in the following order. SLOW 1 4 7 R-TUNE 2 5 8 0 3 6 9 PROG Full Information Channel No display Press this button to display channel number, off-timer remaining time, screen modes, and other settings. PC input mode INFO/RECALL Press this button to display input signal, screen mode, and disappears after 3 seconds. Following screen is displayed in PC input mode. PC NORMAL PC Input selected ASPECT mode OFF TIMER 30 OFF TIMER status (See page 45) 27 Adjusting screen POSITION/SIZE (TV, VIDEO input mode) Adjusting screen 1 2 ASPECT Press to select the screen mode to adjust. LIGHT POWER MENU ASPECT Press to display the MENU. MUTE TV/VIDEO DVD AUX CBL CH R VC RC VR DB S DTV CH Press to select ADJUST menu. VOL TV MENU ADJUST SET UP VOL MENU CH SURROUND NORMAL OFF TIMER VOL ACTION PICTURE PICTURE ADJUST POSITION / SIZE AUDIO SOUND ADJUST AUDIO MODE ACTION VOL INFO/RECALL PC CH EXIT VCR REC GUIDE REW PAGE EXIT ACTION SELECT STOP PLAY FF TV/VCR OPEN/CLOSE VCR/DBS CHANNEL PAUSE STILL SLOW 3 VOL CH POSITION / SIZE NORMAL 1 4 7 R-TUNE 2 5 8 0 3 6 9 PROG Press to select POSITION/SIZE. ACTION VOL SIZE 1 POSITION NORMALIZE CH Press to display the POSITION/SIZE screen. Notes: This unit is equipped with various screen modes. If a screen mode with a different aspect as the broadcast program is selected, image will appear differently. Select the proper screen mode with this in mind. Be careful when using this unit for commercial purposes or for public use, such as in cafes and hotels, for shrinking and enlarging images by using screen mode switching function (zoom, etc. ) may violate copyright laws. [. . . ] A black stripe appears for a moment when changing channels using the VCR. During Panasonic AUTO mode, the screen size sometimes changes. · Are the batteries dead or inserted incorrectly?· Is the remote control sensor in direct light of florescent lamps or other strong sources of light? 6 ­ ­ 8, 9 ­ ­ ­ ­ · Is the antenna or antenna cable old, broken or shorted?· Is the antenna cable connected properly? [. . . ]