User manual PANASONIC TX-32LXD700

[. . . ] Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households) This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, please take these products to designated collection points, where they will be accepted on a free of charge basis. Alternatively, in some countries you may be able to return your products to your local retailer upon the purchase of an equivalent new product. Disposing of this product correctly will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. [. . . ] Make a note of the PIN number in case you forget it. 0 Advanced Enter your name, address, and post code, in that order Check the message and initialise Shipping Condition Select the entry field set To check the "personal information" stored F Restore Settings Shipping Condition All tuning data will be erased Are you sure?Are you sure? Confirm EXIT RETURN Input owner ID Owner ID Enter the "User input" mode Select the character Set RETURN Hold down for about 3 sec. F TV AV Displays the information on the screen (for several sec. ) Owner ID Follow the on-screen instructions · NAME HOUSE NO POSTCODE EXIT A · The PIN number is not displayed. "Auto Setup" will automatically start when Mains power On / Off switch is next turned On. 30) Store To re-tune TV channels only, e. g. after moving house To change the PIN number access Select the "PIN" field select Enter a new PIN number twice 32 33 Input Labels For easier identification and selection of the input mode, you can label each input terminals or skip terminal that is not connected to any equipment. 16) Displaying PC Screen on TV The screen of the PC connected to the TV can be displayed on the TV. You can also listen to PC sound with the audio cable connected. 44) INPUT 1 INPUT OPTION SD CARD EXIT Display the menu 1 2 Select the external input OPTION SD CARD EXIT Select "PC" Input Selection access RETURN 2 3 Select "Setup" Main Menu VIERA Link Picture Sound Setup RETURN access select AV1 AV2/AV2S AV3/AV3S COMPONENT PC HDMI1 HDMI2 HDMI3 TV select · · · Corresponding signals (p. 49) If "H-freq. " or "V-freq. " is shown in red, the signals may not be supported. Displaying PC Screen on TV Input Labels To return to TV Select "Input Labels" Setup Menu 2/2 · access PC menu setting (changed as desired) Preferred Subtitles Shipping Condition Owner ID Common Interface System Update Input Labels Banner Display Timeout VIERA Link Software Licence English select Access 3 seconds On · Menu Picture To make settings "How to Use Menu Functions" to (p. 21) Item R-Gain Adjustments / Configurations (options) Adjusts the white balance for red areas Adjusts the white balance for green areas Adjusts the white balance for blue areas (2. 0 / 2. 2 / 2. 5) Advanced G-Gain PC Settings B-Gain Gamma Input Resolution Clock 4 TV Select a input terminal and set Input Labels 1 of 2 To return to TV EXIT AV1 AV2/AV2S AV3/AV3S COMPONENT PC HDMI1 HDMI2 HDMI3 DVD AV2/AV2S AV3/AV3S COMPONENT PC HDMI1 HDMI2 HDMI3 Set to the minimum level if noise occurs Adjusts horizontal position · · Switches to a wide view VGA (640 × 480 pixels), WVGA (852 × 480 pixels), XGA (1, 024 × 768 pixels), WXGA (1, 366 × 768 pixels) Options change depending on signals Advanced set select H-pos Setup The labels you set will be displayed in "Input Selection" menu (p. If "Skip" is selected, you cannot select the mode. · User input Select "User input" select access PC Setup V-pos Adjusts vertical position You can name each input terminals freely. Set characters User input Clock Phase Store select RETURN · · Eliminates flicker and distortion Adjust after Clock adjustment · Set to the minimum level if noise occurs Name ABCDE UVWXY abcde uvwxy FGHI Z 01 fghi z()+ J 2 j K 3 k . LMNOPQRS 456789!: lmnopqrs *_ T # t Sync set Chooses another synchronous signal if the image is distorted (H & V / On G) H & V : by the horizontal and vertical signals from your PC On G : by the green signal from your PC (if available) (maximum: ten characters) · Other items p. 23 34 35 Recording Controls (DVB mode) Timer Programming from Menu The Timer programming menu allows you to choose programmes that you wish to record. At the correct time, the DVB system will switch on and tune to the correct station (even if the TV is in Standby mode). If the recording equipment is compatible with Q-Link or similar technologies (p. 40) and connected to the TV's AV2 terminal using a SCART cable (p. 44), you do not need to programme the device ­ the DVB system will control the recording process. TV Guide may also be used to set timer programmes. 14) If in Analogue mode Start making the settings start Repeat the operations as below, and set items in the order of to select the item Wed 05/08/04 18:50 set 1 2 3 4 5 6 , and can also be entered with numeric buttons. Select DVB DVB Timer Programming INPUT Previous timer programming event Current timer programming event P o s. N am e 1 3 BBC1 ITV1 D ate 6/8 FR 7/8 SA S tar t 18:00 21:30 En d 20:00 22:30 min. 120 60 Off Off Subtitles (Off / Auto) Recording time (automatic display) OPTION SD CARD Display the menu EXIT Set timer programming details Channel Date one day ahead daily or weekly (press repeatedly) Ending time Starting time RETURN Select "Setup" Main Menu VIERA Link Picture Sound Setup access Daily SU-SA: Sunday to Saturday Daily MO-SA: Monday to Saturday Daily MO-FR: Monday to Friday Weekly SA/FR/TH/WE/TU/MO/SU: Same time on the same day every week · Recording Controls select To change a timer programming event Select the programme to be changed using Correct as necessary (as above) and press Select "DVB Timer Programming" Setup Menu 1/2 To cancel a timer programming event access Select the programme to be deleted using and press red DVB Timer Programming DVB Profile Edit DVB Service List Q-Link Settings Child Lock Tuning Menu Off Timer Power on Preference Teletext Access select Off Off TV FASTEXT Direct TV recording: You can record the current programme to DVD Recorder or VCR immediately. 40) Set To return to TV EXIT · · · · · store Note Confirm the DVB LED lights (Orange). If not, a timer programming is not available. A message will appear if you try to programme a timer event which overlaps an already programmed event. [. . . ] The timer programme events are overlapped. Cannot record other channel at the same time. Check the Starting and Ending times in Timer Programming (p. If you want to unlock, cancel Direct TV Recording (p. [. . . ]