User manual PANASONIC TX-50CX680E

[. . . ] Retain your purchase receipt also, and note down the Model Number and Serial Number of your set in the space provided on the rear cover of these Instructions. Visit our Panasonic Web Site http://www. panasonic. co. jp/global/ Important Information (1) The long time (max. 2 hours) use of a TV game on this set is not recommended, since the signal from the TV game may cause damage to the picture projection tubes of the set. (2) Do not allow a still picture to be displayed for an extended period, as this can cause a permanent afterimage to remain on the Projection TV screen. [. . . ] (Becomes a white line) Press N button to adjust the blue mode. (Stores RED) 1 RED 2 3 4 TV / AV -EXIT N-BLUE 6 7 8 9 BLUE Press to align the horizontal blue line with the horizontal yellow line. (Becomes a white line) Press to align the vertical blue line with the vertical yellow line. (Becomes a white line) Repeat above adjustment for each position. TV/AV 1 BLUE 2 3 4 TV / AV -EXIT N-RED 6 7 8 9 Press to return to the normal viewing. (Stores BLUE) Note: If you wish to view a video with a different colour system (PAL / SECAM, NTSC), repeat the steps above while displaying a picture. 20 Tuning Channels 1 Display the TUNING MENU 1 2 Press to select the TUNING MENU. SET UP SETUP MENU TELETEXT OFF TIMER FLICKER REDUC. STROBE CH COLOUR SET VCR / GAME TEXT SELECT FASTEXT OFF DYNAMIC SETUP MENU CHILD LOCK OFF PICTURE SHIFT OFF ACCESS TUNING MENU CONVERGENCE LANGUAGE ENGLISH Press to display the SETUP MENU. OFF ENGLISH Press to display the TUNING MENU. 2 1 Select the "POSITION" or the "DIRECT" CH SELECT Press to select the "CH SELECT (Channel Select) " Mode. Press to select the "POSITION" or the "DIRECT". Setting range when the "POS. " (Position) has been selected: Position 0-99 Setting range when the "DIRECT" has been selected: Channel 0-125 The channel select indicator will change as follows. DIRECT TUNING MENU CH SELECT SYS SELECT AUTO TUNE MANUAL TUNE SOUND SYS COLOUR SYS FINE TUNE SKIP POSITION ASIA / M. EAST 5. 5 MHz AUTO OFF POSITOIN 2 Regional System Selection SYS SELECT (Before AUTO tuning and MANUAL tuning, set the "SYS SELECT" mode, as detailed below. ) Press to select the "SYS SELECT". The system select indicator will change as follows. CHINA JAPAN HK/UK CATV ASIA/M. EAST AMERICA NZ/INDONES SPECL VER AUSTRALIA E. EUROPE TUNING MENU CH SELECT SYS SELECT AUTO TUNE MANUAL TUNE SOUND SYS COLOUR SYS FINE TUNE SKIP POSITION ASIA / M. EAST 5. Press to access to the MANUAL TUNE. TUNING MENU CH SELECT SYS SELECT AUTO TUNE MANUAL TUNE SOUND SYS COLOUR SYS FINE TUNE SKIP POSITION ASIA / M. EAST ACCESS 5. 5 MHz AUTO OFF 2 Press to select the desired Programme Number. Press to select the higher or lower channel. Search Start. 29 CH 12 When a station is found. PROGRAMME - /+ SEARCH - /+ TV / AV - EXIT `STR' BUTTON-STORE RETURN MANUAL TUNE STR When the desired station is found, press to store. The tuning position is memorised. TV/AV Press to exit from the Tuning Menu. This returns the set to the normal viewing condition. 2 SOUND SYS SET UP Press to display the SETUP MENU. Proceed to the TUNING MENU, and then to the SOUND SYS ( refer to page 28). 3 Adjust the Sound System ( refer to page 24 step 2 to 3). Helpful Hint (1) If a clear picture with correct colours cannot be obtained when a Broadcast or AV signal is received, refer to the "Colour System Selection" operation on page 28. (2) After the Manual tune is finished, under the normal viewing condition press this button to confirm the tuning condition for each Programme Number. If some Programme Numbers are unused (no TV stations), it is possible to skip such Programme Numbers. Please refer to the Programme Number Skip operation on page 27. (3) When using a VCR without video and audio input/output terminals, it is convenient to connect the aerial cable as indicated in the instruction manual of VCR and to set the designated channel to programme No. [. . . ] Type of broadcast Mode Indicator Regular broadcast (Standard Audio) No Indicator BILINGUAL or DUAL MONO: MAIN I / SUB II I II STEREO Notes: · If the stereo signal is poor or the receiving conditions are not optimum or if STEREO:MONO automatic switching occurs, it is recommended you switch from STEREO to MONO. · Even when the contents of the receiving signal undergo changes, selection mode is kept intact. · When the receiving conditions deteriorate, listening will be easier if the mode is set to the "MONO" position, using the stereo/bilingual sound selection button. · "DUAL", also known as "DUAL MONO" or as "BILINGUAL" is not currently transmitted in some countries. VCR / LD / DVD Control The Remote Control is capable of operating some functions of selected Panasonic VCRs, LD and DVD (Digital Versatile Disc) equipment. [. . . ]