User manual PANASONIC TX-D7F21M

[. . . ] Insert the mains plug fully into the socket outlet. (If the mains plug is loose, it could generate heat and cause fire. ) Do not touch the mains plug with a wet hand. (This may cause electrical shock. ) Power source This TV set is designed to operate on 220-240V, 50 Hz AC. Note If the set is not switched off when the TV station stops transmitting, it will automatically go to standby mode after 30 minutes. This function will operate only in TV mode. Do not expose to direct sunlight and other sources of heat Avoid exposing the TV set to direct sunlight and other sources of heat. [. . . ] 20). To reset the setting N · · 16 Resets each Viewing mode (Dynamic / Normal / Cinema / Auto) to the default settings. Aspect mode is also reset to Auto aspect. Menu list Menu Item Viewing mode Adjust by each viewing mode Tuning menu Adjustments / Configurations (alternatives) Selects four different screen settings (Dynamic / Normal / Cinema / Auto) In each Viewing mode setting, Contrast, Brightness, Colour, Sharpness, Tint (in NTSC only), Colour balance, P-NR and 3D-COMB can be adjusted and stored to suit your particular viewing requirement (e. g. , you may require different settings for viewing sports, films, news etc. ) Changes to any settings in a viewing mode will affect all signal sources: RF, AV1, AV2, AV3, Component and HDMI1, 2. By analysing and processing the incoming picture, all four modes feature automatic enhancement. · Picture menu Sound menu Setup menu Contrast, Brightness, Increases or decreases the levels of these options according to your personal preference Colour, Sharpness With an NTSC signal source connected to the TV, the picture hue can be adjusted to suit your taste Tint Allows you to set the overall colour tone of the picture (Cool / Normal / Warm) Colour balance P-NR 3D-COMB Picture Noise Reduction Automatically reduces unwanted picture noise (Off / Min / Mid / Max) Not valid on HDMI and HD signal Occasionally, whilst viewing still or slow moving pictures, colour patterning may be seen Set to On to display sharper and more accurate colours (Off / On) For PAL or NTSC signal reception only Not valid on RGB, S-Video, components and HDMI Bass Treble Balance Headphone volume NICAM Mode Ambience · · · Increases or decreases level to enhance or minimise lower, deeper sound output Increases or decreases level to enhance or minimise sharper, higher sound output Adjusts volume level of right and left speakers Adjusts the volume of the headphones NICAM (Near Instantaneous Companded Audio Multiplex) A format for digital sound over television Reproduces stereo sound (Off / On) Off if reception is poor (FM monaural sound) Sound quality can be improved when watching music scene or drama (Music / Speech) · How to Use Menu Functions (picture, sound quality, etc. ) · Provides a dynamic enhancer to simulate improved spatial effects (Off / On) Select to fit the input signal (Auto / Digital / Analogue) (p. 23) Auto : Automatic detection of digital or analogue sound source Digital : HDMI cable connection Analogue : HDMI-DVI adapter cable connection HDMI input mode only HDMI2 terminal is for digital signal only No setting for HDMI2 available HDMI1 input VIERA Link Q-Link AV1 out AV2 out Teletext Off timer Volume correction Power on preference Programme edit Auto setup Manual tuning Fine tuning Owner ID Shipping condition · · · · · · · · VIERA Link function (Off / On) (p. 24) Selects which AV terminal is to be used for data communication between this TV and a compatible recording equipment (AV1 / AV2) (p. 22) Chooses the signal to be transmitted from the TV to Q-Link (TV / AV2 / AV3 / Monitor) Monitor: Image displayed on screen Component and HDMI signals cannot be outputted Chooses the signal to be transmitted from the TV to Q-Link (TV / AV1 / AV3 / Monitor) Monitor: Image displayed on screen Component and HDMI signals cannot be outputted Teletext display mode (FASTEXT / List) (p. 12) Sets the time the unit automatically turns Off. (Off / 15 / 30 / 45 / 60 / 75 / 90) (minutes) Adjusts volume for AV and HDMI mode Set to "TV" to view picture from TV tuner. Set to "AV" to view input from an external equipment connected to a SCART terminal, e. g. satellite receiver (TV / AV) The external equipment must be switched on and sending a control signal for automatic switching at power on to occur Edits channels (p. 19) Fine tuning of channels (during rain, etc. ) Inputs the owner ID (p. The recording equipment is recording from its own tuner. You can turn the TV off during recording. If, during recording from an AV source, you turn the TV off or change input / programmes, the recording will be stopped. Information / Message Recording information or if recording is not possible, a message is displayed. (Only when the programme number is "0" or "AV mode" for some equipment. ) Power on link and Easy playback When VCR or DVD recorder starts playback or direct navigator or function menu are activated, the TV is turned on and input mode is switched automatically so that you can view the content. (Only when TV is in Standby mode. ) Power off link When TV is set to Standby mode, the recording equipment is also automatically set to Standby. (Only when the videocassette or DVD is not active. ) · "DATA LOGIC" (a trademark of Metz Corporation) · "Megalogic" (a trademark of Grundig Corporation) · "Easy Link" (a trademark of Philips Corporation) · "SMARTLINK" (a trademark of Sony Corporation) Read the manuals of the equipment too. 22 HDMI Functions HDMI connection HDMI (high-definition multimedia interface) allows you to enjoy high-definition digital images and high-quality sound by connecting the TV unit and the equipment. HDMI-compatible equipment ( 1) with an HDMI or DVI output terminal, such as a set top box or a DVD player, can be connected to the HDMI terminal using an HDMI compliant (fully wired) cable. About connections, see "External Equipment" (p. 26). · · · · · · · · · · · · Note HDMI is the world's first complete digital consumer AV interface complying with a non-compression standard. If the external equipment has only a DVI output, connect to the HDMI1 terminal via a DVI to HDMI adapter cable ( 2). When the DVI to HDMI adapter cable is used, connect the audio cable to the audio input terminal. [. . . ] Check the Q-Link connection and setting (p. The impossible source (Component / HDMI) to be record. The tape or disc may be "write protected", missing or damaged. The equipment may already be recording. The recording cannot be done by any reason. [. . . ]