User manual PANASONIC TX-P50UT30J

[. . . ] Information for Users on Collection and Disposal of Old Equipment and used Batteries These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC and 2006/66/EC. By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. For more information about collection and recycling of old products and batteries, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items. [. . . ] A good Signal Strength is not an indication of suitable signal for DVB reception. Please use the Signal Quality indicator as follows : [Signal Quality] : Green bar Good Yellow bar Poor Red bar Bad (Check the Terrestrial aerial or cable) · To change the channel · · · Example : DVB-C Signal Condition Channel Name Signal Quality Signal Strength Bit Error Rate Network Name Parameter 70 CBBC Channel 90 % 80 % 0. 00E+00 Wenvoe 802, 00 MHz, 64 QAM, 6940 kS/s These bars show the maximum signal value of the selected channel. Tuning and Editing Channels (DVB) Reduce the DVB-C signal [Attenuator] If the DVB-C signal is too strong, the interference may occur. In this case set to [On] to reduce the signal automatically. This function is available only for DVB-C signal. · 50 Tuning and Editing Channels (Analogue) You can retune channels or skip unwanted channels, edit channels etc. 1 2 3 Select Analogue (p. 18) TV Display the menu MENU Select [Setup] Main Menu Picture Sound Timer Setup select access 4 Select [Analogue Tuning Menu] select Analogue Tuning Menu Access access 5 To return to TV EXIT Select one of the following functions Analogue Tuning Menu Channel List Auto Setup Manual Tuning Access Access Access Tuning and Editing Channels (Analogue) select access · · The function items vary depending on the country you select (p. [Auto Setup] "Retuning from Setup Menu" (p. 46) Skip unwanted Analogue channels, Edit Analogue channels [Channel List] You can hide unwanted Analogue channels. The hidden channels cannot be displayed except in this function. Use this function to skip unwanted channels. Select a channel and reveal / hide Analogue Channel List 1 2 3 4 5 6 7 BBC1 ***** ***** ***** ***** ***** ***** select [Reveal] / [Hide] : [Reveal] : [Hide] (skip) · To reveal all channels (yellow) 51 To edit channels You can also edit each channel in Channel List. To retune each channel ([Manual Tuning]) · · (red) (see below) To move the channel position Select the new position (green) Store (green) · To rename the channel name (blue) A U a u Set characters (maximum : five characters) Edit channel name Name B b v CD c w d x E Y e y F Z f z g ( GH 0 h ) I 1 i + J 2 j K 3 k . r S : s T # t VWX Store select set BACK/ RETURN use numeric · To "Characters buttons numeric buttons" (p. 98) table for Channel position Channel name 1 ITV CH23 SC1 23:35 All Analogue Channels · If a VCR is connected only with the RF cable, edit [VCR]. Set Analogue channel manually [Manual Tuning] [Fine Tuning] Use to make small adjustments to the tuning of an individual programme (affected by weather conditions, etc. ) Note [Manual Tuning] Set Analogue channel manually after Auto Setup. Set [Sound System] and [Colour System], and then perform this function. If a VCR is connected only with the RF cable, select channel position [0]. Tuning and Editing Channels (Analogue) · · Analogue Manual Tuning 1 BBC1 Fine Tuning Manual Tuning Sound System Colour System CH33 2 78 1 SC1 Auto Store 41 SC1 : PAL B, G, H / SECAM B, G SC2 : PAL I SC3 : PAL D, K / SECAM D, K F : SECAM L, L' 1 Select the channel position abc ghi pqrs jkl tuv def mno wxyz 2 Select the channel 3 Search 4 Select [Store] select store 52 Timer Programming Timer Programming from Menu The Timer Programming menu allows you to choose programmes that you wish to remind watching or record to the external recorder. At the correct time, the TV will tune to the correct channel even if the TV is in Standby mode. TV Guide may also be used to set timer programming event (p. This function is not available in Analogue mode. Timer Programming can store up to 15 events. Timer Programming only works reliably if correct time information is received via the signal from the broadcaster or service provider. For recording using Timer Programming, the TV must be either On or in standby. For reminders to be displayed, the TV must be On. [. . . ] connected USB device might cause this error. Remove · Thewith Mains power On / Off switch, then turn it On again. the device and turn the TV Off · Check if foreign objects are inside the USB port. · Followproblem persists, contact your local Panasonic dealer or the authorized Service · If the Centre. Cannot connect to the network Network Other Cannot operate VIERA Connect The TV does not switch On The TV goes into Standby mode The remote control does not work or is intermittent Parts of the TV become hot Permanently lit spots on screen Overcurrent error message appears Frequently Asked Questions An error message appears 101 Specifications TX-P42UT30J Power Source Rated Power Consumption On mode Average Power Consumption (based on IEC 62087 Ed. 2 measurement method) Standby Power Consumption AC 220-240 V, 50 / 60 Hz 270 W 315 W TX-P50UT30J 121 W 0. 40 W 16. 00 W (With monitor out recording) 1, 023 mm × 671 mm × 320 mm (With Pedestal) 1, 023 mm × 637 mm × 93 mm (TV only) 27. 5 k Net (With Pedestal) 24. 0 k Net (TV only) 167 W Dimensions (W × H × D) 1, 212 mm × 782 mm × 335 mm (With Pedestal) 1, 212 mm × 747 mm × 93 mm (TV only) 35. 0 k Net (With Pedestal) 31. 0 k Net (TV only) Mass Display panel Sound Aspect Ratio Visible screen size Number of pixels Speaker Audio Output Headphones 16:9 106 cm (diagonal) 921 mm (W) × 518 mm (H) 127 cm (diagonal) 1, 105 mm (W) × 622 mm (H) 2, 073, 600 (1, 920 (W) × 1, 080 (H)) [5, 760 × 1, 080 dots] (160 mm × 40 mm) × 2, 20 W (10 W + 10 W) M3 (3. 5 mm) stereo mini Jack × 1 PAL B, G, H, I, SECAM B, G, SECAM L, L' PAL D, K, SECAM D, K PAL 525/60 M. NTSC DVB-T DVB-C VHF / UHF Temperature : 0 °C - 35 °C Humidity : 20 % - 80 % RH (non-condensing) 21 Pin terminal (Audio/Video in, Audio/Video out, RGB in, Q-Link) VIDEO AUDIO L - R Y PB, PR RCA PIN Type × 1 RCA PIN Type × 2 1. 0 V[p-p] (including synchronization) ±0. 35 V[p-p] 1. 0 V[p-p] (75 ) 0. 5 V[rms] VHF E2 - E12 VHF A - H (ITALY) CATV (S01 - S05) CATV S11 - S20 (U1 - U10) VHF R1 - R2 VHF R6 - R12 VHF H1 - H2 (ITALY) UHF E21 - E69 CATV S1 - S10 (M1 - M10) CATV S21 - S41 (Hyperband) VHF R3 - R5 UHF E21 - E69 6 Receiving Systems / Band name Check the latest information on the available services at the following website. (English only) http://panasonic. jp/support/ global/cs/tv/ Playback of NTSC tape from some PAL Video recorders (VCR) Playback from M. NTSC Video recorders (VCR) Digital terrestrial services (MPEG2 and MPEG4-AVC(H. 264)) Digital cable services (MPEG2 and MPEG4-AVC(H. 264)) NTSC (AV input only) Playback from NTSC Video recorders (VCR) Aerial input Operating Conditions AV1 (SCART) Connection Terminals AV2 input COMPONENT input Specifications HDMI 1 / 2 / 3 input TYPE A Connectors HDMI1 / 3 : 3D, Content Type, Deep Colour, x. v. ColourTM HDMI2 : 3D, Content Type, Audio Return Channel, Deep Colour, x. v. ColourTM This TV supports "HDAVI Control 5" function. · 102 Card slot ETHERNET USB 1 / 2 AUDIO IN AUDIO OUT DIGITAL AUDIO OUT SD Card slot × 1 Common Interface slot (complies with CI Plus) × 1 RJ45, IEEE802. 3 10BASE-T / 100BASE-TX USB2. 0 DC 5 V, Max. [. . . ]