User manual PANASONIC TY-27G22M

[. . . ] Assistance may be required for some assembly procedures. CAUTION : THIS STAND IS DESIGNED ONLY FOR USE WITH A PANASONIC PLASMA TV. APPLIED MODEL : TH-42PX20, TH-50PX20 Use with other appliances may result in instability causing possible injury. [. . . ] Your hardware pack contains / Replacement parts Assembly screws Glass shelf fastening screws Glass shelf support fastening screws (Black screws) ( × 4) Rear cord cover fastening screws (Black screws) ( × 3) Support pole insertion hole Assembly screws (Black screws) Support pole (Right) STEP 2 To use with equipment such as a video deck Wire over the minimum distance · To thread wiring, remove the terminal cover and pass wires along the THEA118 × 4 Support pole fastening screws THEA102N × 8 Assembly screws (Black screws) XST5+12 × 4 Support pole (Right) XYN5+F55FZ × 4 Support pole (Left) XSB4+12FZ × 7 Cord clamps grooves in the rear cord cover, along the groves in the left and right side panels, and along the groves in the cord holder under the glass shelf. In such an instance, thread the wiring over the minimum distance, as indicated by the dotted line in the diagram. · After threading wiring, fasten with cord clamps (× 6) so that the cords do not protrude from the grooves. If there are any cord clamps left over, store them carefully. You will need them if you use the unit to house more equipment in the future. The top glass shelf is specifically for the center speaker and AV amp. If you place a video deck here, it may badly affect the picture. (Back) Cord clamps Power cord TBLA3196 × 1 Glass shelf supports (Right) TBLA3197 × 1 Glass shelf supports (Left) TBLB3111 × 6 Casters (Wheels) REPLACEMENT PARTS LIST TY-S42PX20U Qty. Description 1 TBLA0116 Top crosspiece 1 TBLH0548 Bottom panel 1 TBLA0104 Side panel (Left) Side panel (Right) 1 TBLA0103 1 TBLB3080 Rear cord cover 1 TKGA0127 Glass shelf 1 TBLA3184 Cord holder TY-S50PX20U Part No. in the same Side panel (Left) Glass shelf supports (Left) Dowel holes Dowel holes 3. Insert a cord holder in parallel with the glass shelf supports (left and right), and align the dowels of the cord holder with the dowel holes in the glass shelf supports. Attach the other cord holder to the other glass shelf supports in the same manner. Glass shelf support fastening screws (Black screws) STEP 2 Attaching of top crosspiece and rear cord cover Support pole fastening screws Support pole (Right) Top crosspiece Glass shelf supports (left and right) 1. Align the support pole (right) with the notch on the right side of the top crosspiece, and securely fasten with the support pole fastening (× 2) using a Phillips head (+) screws screwdriver. Fasten the support pole (left) to the left side in the same manner. Notches Rear cord cover 2. Insert the rear cord cover fastening screws (× 3) into the screw holes on (black screws) the back of the top crosspiece and partially fasten. Slide the 3 notches in the rear cord cover behind the screws and securely fasten the screws. Notches 4. Attach the caution label to one glass shelf on the right side, facing the front. [. . . ] Attach the caution label to one glass shelf on the right side, facing the front. Insert the glass shelf in parallel with the grooves in the glass shelf supports (left and right), and securely fasten to the bottom of the (left and right) glass shelf supports using the glass shelf fastening screws (× 4). Fit the other glass shelf in the same manner. Dowel / hole Cord holder Glass shelf Caution label Rear cord cover fastening screws (Black screws) Assembly screws Side panel (Right) Glass shelf fastening screws 3. [. . . ]