User manual PANASONIC TY-UPK110

[. . . ] TY-UPK110 2 3 B B A B B A A C A B B B A B C 4 33 CD CD 5 C Matsushita Electric Industrial Co. , Ltd. 2001 Matsushita Electric Industrial Co. , Ltd Web Site: http://www. panasonic. co. jp/global/ Printed in Japan MS0601-1102 Setting the fan motor software Be sure to confirm the software settings are completed under the procedure below. By this software settings the fan will detect its mulfunctions and stop operation to avoid possible accidents. Note: Instructions vary depending on the display. 1) While pressing and holding the VOL button on the display. [. . . ] 6) Press the VOL or VOL button on the remote control to change field on the screen from 0 to 1. Enlarged view of CD mode display CD CD 7) Turn the power off by pressing the Power button on the display. 5 Prepare the Wide Plasma Display 1) Remove the rear cover from the display. Place the display facing downward on a clean blanket or the like, and follow the steps below. B Remove 4 A bolts, 16 B screws, and B B 5 C screws from the display (25 bolts A B and screws). A A C A B B B A B C Put the rear cover and removed bolts and screws to the side where they will not get lost. 2) Attach the cooling fans and cooling fan relay printed circuit board. Install the 4 cooling fans and cooling fan relay printed circuit board at the locations shown in the figure on the left, using the supplied mounting screws (M3). First lightly tighten mounting screws through and through , then temporarily tighten screws through together with the cooling fan relay printed circuit board. After properly positioning each fan, tighten screws firmly. ) Caution · Be sure to position the cooling fans correctly in the display. 3) Attach the connectors. Connector for cooling fans Connect cooling fan leads into connectors FA2, FA3, FA4, and FA5. Connect one end of each of the supplied leads to the inline connection board and the other ends to Power Supply Printed Circuit Board P10. Secure all fan leads with the wire clamps as shown. Connector (P10) 4) Reattach the rear cover. Reverse the steps given above for removing the cover. Insert the 25 screws and tighten the screws. 4 Components Cooling fan 4 Cooling fan relay printed circuit board 1 Cooling fan mounting screw (M3) 13 Points to note during installation This optional cooling fan kit is designed exclusively for use with this display model. In order to ensure correct, problem-free operation of the Wide Plasma Display, do not install the Display in any of the following places. · Places which are next to sprinklers or sensors · Places which are subject to vibration or shocks · Places which are close to high-voltage wires or electric motors · Places in direct contact with air from heaters When installing the wall-hanging bracket unit, use a mounting method appropriate to the type of wall. This kit does not include the bolts needed to mount the bracket to the wall. Please purchase screws suitable for the material (wood, steel frame, concrete, etc. ) of the wall on which the bracket and Wide Plasma Display are to be mounted. Insert the power cord plug for the Wide Plasma Display into a wall outlet which is close and easily accessible. Provide adequate ventilation so that the temperature around the display does not rise above 40 . If there is insufficient movement of air inside the display, heat may build up inside the display, and fire may result. 3 Thank you very much for purchasing the Plasma Display cooling fan Kit. Installation work should only be carried out by a qualified technician. · If the unit is installed incorrectly, the display may fall down and personal injury may result. Precautions with regard to setting up WARNING Always have a service technician perform the installation. [. . . ] · These can have adverse effects on Wide Plasma Display operation, and fire or electric shocks may result. Two people are required to install and remove the display. · If two people are not present, the display may be dropped, and personal injury may result. 2 TY-UPK110 Plasma Display Cooling Fan Kit Installation Instructions Before attempting to install this kit, please read these instructions completely. TQZH333-1 [. . . ]