User manual PANASONIC TYWK103PF9

[. . . ] This may cause heat to build up inside the plasma display, resulting in a fire. Do not fit at any locations subject to humidity, dust, smoke, steam or heat. When using the wall-hanging bracket, do not block the space between the rear surface of the plasma display and the wall surface. Otherwise heat may build up inside and cause a fire. [. . . ] Do not subject it to a strong force or impact. This bracket is intended for only Panasonic plasma display models (See page 71). Base upper and lower fitting (2) Bracket base left fitting (1) Bracket base right fitting (1) Screw for assembling the fixture (4) M5×10 View of fully assembled fixture Allen head countersunk screw (4) M8×32 Screw for securing unit (2) M5×50 [The images shown in this manual are for illustrative purpose only. The wall-hanging bracket is for use in attaching a plasma display unit to a vertical wall for viewing. Do not fit to any surface other than a vertical wall. To ensure correct plasma display performance and prevent trouble, do not fit at any of the following locations. Where there is a risk of exposure to vibration or impact · Near high-voltage wires or dynamic power supplies · Near sources of magnetism, heat, water vapor or soot · locations exposed to air blown from heating equipment · Where droplets of condensation from an air conditioner or other unit may form Fit using techniques suited to the structure and materials of the fitting location. Use commercially available screws with a nominal diameter of 6 mm (0. 2 inches) that are suited to the wall material (wood, steel frame, concrete etc. Ensure good air flow so that the ambient temperature does not exceed 40 °C (104 °F). Failure to do this may cause heat to build up inside the plasma display, resulting in malfunction. Use screws that are sufficiently strong. install the wall-hanging bracket so that the arrows indicated on it are pointing upward. First of all, secure the screw in the upper center hole . Use a level to ensure that the bracket is not inclined at an angle, and screw the bracket into position using the three screw holes at the bottom. Remove the angle adjustment screws from the bracket base left and right fittings, and open the bracket base left and right fittings. Screw the bracket into position using the screws at the remaining two screw holes at the top. Use the angle adjustment screws, which were removed, to perform the angle adjustment of step 4. The angle of this wall-hanging bracket can be adjusted in 5-degree increments to one of five positions ranging from "Zero tilting" to "20-degree tilting". M) When the angle is set When the angle is set to "Zero tilting" to "15-degree tilting" Stay "Zero tilting" Surface of wall Surface of wall Cap Angle adjustment screws When using some types of HDMI cables (RP-CDHG80 or RP-CDHG100) or PC cables, the cable may touch the wall and cause damage to the HDMI terminal or the PC input terminal on the plasma display. Attaching the insulation spacers Place the front surface of the plasma display on a clean cloth that has no dirt or foreign objects on it, and follow the procedure below. If the plasma display has any protruding parts, take care not to scratch or damage them. [. . . ] After the bottom insulation spacers have been removed, continue lifting up the plasma display and remove it. Screw for securing unit Install the accessory screws for securing unit (2) into the Screw for securing unit mounting holes of the screws for securing unit on the sides (left and right) of the wall-hanging bracket. Hole for mounting the Securely tighten the removed red-marked pivot fixing/releasing screw for securing unit screws (one at the left and one at the right) in the mounting holes of the red-marked pivot fixing/releasing screws on the Mounting hole for red-marked sides of the wall-hanging bracket. Mounting the plasma display onto the wallhanging bracket and connecting it to the other components Boven- en onderprofielen (zijde waarop het naamplaatje van het model bevestigd is) Buitenkant (A): model 58V Binnenkant (B): model 42/50V Cuando quite la pantalla de plasma, quite también las abrazaderas de suspensión de pared. [. . . ]