User manual PANASONIC TY-WK32LH1U

[. . . ] Inadequate installation may cause the LCD TV to fall, resulting in bodily injury. Be aware of safety factors concerning the mounting strength. Insufficient strength may cause the LCD TV to fall, resulting in bodily injury. Do not hang from the LCD TV, place stepsladder, etc. [. . . ] Notes · There are 12 holes in the wall hanging bracket. If the wall material is wood, and adequate attachment strength cannot be ensured by fastening at the 6 points at right, use as many spare holes as necessary. However, exercise care because some wall materials may crack if screws are located too close together. Do not fit at any location where these dimensions cannot be secured. 2. Fit wall hanging bracket to wall · Fit so that the arrow marks on the wall hanging bracket point upward. · If the wall consists of a material such as concrete and bolts or nuts must be embedded beforehand, determine the hole positions by aligning using the actual wall hanging bracket, or calculate hole positions based on the dimension drawing, and then embed "M6" bolts or nuts. When embedding bolts, locate so that the bolts protrude from the wall by 10 mm (25/64 inches) to 15 mm (19/32 inches). (1) Fasten the screw at the top center hole first. (2) Using a level, correct any bracket inclination, and then fasten screws at the remaining 5 locations. Note · Use commercially available M6 screws suited to the wall surface material (wood, steel frame, concrete etc. ) for fitting the bracket to the wall. Prepare the LCD TV Fit the insulation spacers to the LCD TV. Place the LCD TV unit face down on a blanket or other soft cloth that is clean and free of debris, and follow the procedure below. Tuner section cover (1) Remove the terminal section cover on the left side of the LCD TV, and the tuner section cover at the bottom center. * Keep the removed covers in a safe place. (They will be needed again Stand if you decide to change to a spepole hole Bottom cial-purpose or floor-type stand. ) Terminal stickers section cover Inclined surface (2) Affix the enclosed bottom stickers (1 each for left and right) to the stand pole holes at the bottom center of the LCD TV. (Affix the bottom stickAllen head countersunk screw ers by peeling off the separator, Dished toothed washer aligning the perforations and folding Insulation spacer at a right angle, as shown in the diaAllen wrench gram. ) (3) Fit the enclosed Allen head countersunk screws, dished tooth washers and insulation spacers (4 each) as shown in the diagram at right and tighten using the included Allen wrench. 4. Fit and fasten the LCD TV unit to the wall hanging bracket (1) Hook the insulation spacers on the top of the LCD TV into the notches at the top of the wall hanging bracket. (2) Insert the bottom insulation spacers while lowering the LCD TV, and then gently allow it to drop down. (3) Attach securely using the included unit fastening screws (1 each for left and right). Insulation spacer (1) Wall hanging bracket Red screw for open / close fastening LCD TV Upper notch Wall Insulation spacer Lower hole (2) (3) Screw for LCD TV unit fastening Wall Screw securing hole for LCD TV unit fastening Note · Always fit the unit fastening screws to ensure that the LCD TV unit cannot be accidentally dislodged from the wall hanging bracket. ­5­ 5. Center speaker fitting and wiring * The SB-PC50 center speaker for home theater (sold separately) can be fitted to the wall hanging bracket. (1) Remove the red screws for open/close fastening (one each on the left and right) . (2) Tentatively fasten by lifting up the LCD TV towards yourself, as shown in the diagram at left, pressing the lock bracket upward in the arrow direction (up), and checking that the bracket is locked. Securely fasten the red screw for open/close fastening (one screw on the left) in the lock bracket fastening hole . (3) Securely fasten the SB-PC50 to the speaker bracket using the included speaker fastening screws (x2). (4) Insert the speaker bracket into the speaker bracket attachment holes on the wall hanging bracket, and securely fasten with the included speaker bracket fastening screw (x1). [. . . ] Do not fit to any surface other than a vertical wall. The equipment has a lock mechanism on the left side, so provide at least 300 mm (11 13/16 inches ) of space from the wall surface. To ensure correct LCD TV performance and prevent trouble, do not fit at any of the following locations. · Near sprinklers or fire/smoke detectors · Where there is a risk of exposure to vibration or impact · Near high-voltage wires or dynamic power supplies · Locations exposed to air blown from heating equipment Fit using techniques suited to the structure and materials of the fitting location. [. . . ]