User manual PANASONIC TY-WK42PV3U

[. . . ] Confirm the strength of the proposed fitting location The weight of the wall hanging bracket is approximately 7 kg (15 lb. ). The plasma TV unit attached to the wall hanging bracket weighs approximately 30 to 56 kg (66 to 123 lb. ). Check the wall strength at the 6 attachment locations by referring to the dimension drawing of the wall hanging bracket (given at right), and provide adequate reinforcement if strength is not sufficient. A 775 (30 33/64) 735 (28 15/16) 660 (25 63/64) Note Wall Plasma TV external profile · There are 22 holes in the wall hanging bracket. 23 (29/32) 415 (16 11/32) 370 (14 9/16) 320 (12 19/32) B If the wall material is wood, and adequate attachment strength cannot be ensured by fastening at the 6 points at right, use as many spare holes as necessary. However, exercise care because some wall materials may crack if screws are located too close together. [. . . ] (2) Securely fasten the red screws for open/close fastening (one each on the left and right) to the fitting holes on the side of the unit. Wall hanging bracket Wall · Fit so that the arrow marks on the wall hanging bracket point upward. · If the wall consists of a material such as concrete and bolts or nuts must be embedded beforehand, determine the hole positions by aligning using the actual wall hanging bracket, or calculate hole positions based on the dimension drawing, and then embed "M6" bolts or nuts. When embedding bolts, locate so that the bolts protrude from the wall by 10 to 15 mm (25/64 to 19/32 inches). (1) Fasten the screw at the top center hole first. (2) Using a level, correct any bracket inclination, and then fasten screws at the remaining 5 locations. Note · Use commercially available M6 screws suited to the wall surface material (wood, steel frame, concrete etc. ) for fitting the bracket to the wall. 3. Prepare the plasma TV (1) Fit the insulation spacers to the plasma TV. Note Place the plasma TV unit face down on a blanket or other soft cloth that is clean and free of debris, and follow the procedure below. · Be sure to always fit the red screws for open/close fastening in order to fasten the plasma TV. Lock bracket Red screw for open/close fastening Lock bracket fastening hole Fitting hole for red screw for open/close fastening Red screw for open/close fastening 7. Removal of plasma TV unit Wall hanging bracket Wall Wall (3) (1) Remove the terminal cover on the plasma TV (PX20 series only). (2) Using a flathead screwdriver, remove the four caps from the plasma TV. * Carefully retain the removed terminal cover and caps in a safe place. (They will be needed again later should it be required to use the specialpurpose stand or standalone stand. ) (3) Using the included Allen wrench, fit the included Allen head countersunk screws, dished tooth Caps washers and insulation spacers (4 sets) into the holes from where the caps were removed. (See the diagram at right. ) Flathead screwdriver (1) Remove the screws for unit fastening (1 each on the left and right) that are fitted to the wall hanging bracket sides. (2) While lifting the bottom of the plasma TV unit, pull it towards yourself. (3) When the lower insulation spacers are freed, keep lifting upward. (1) Screw for plasma TV unit fastening (2) Insulation spacer Allen head countersunk screw Dished toothed washer Insulation spacer Allen wrench Terminal cover Matsushita Electric Industrial Co. , Ltd. Web Site : http://www. panasonic. co. jp/global/ C Matsushita Electric Industrial Co. , Ltd. 2003 TQZH498 Safety precautions TY-WK42PV3U Wall hanging bracket (Vertical mounting type) Allen wrench ( included tool ) . x1 Always follow these precautions Components The following precautions must be followed in order to prevent danger to the user or other people, as well as equipment damage. The labels shown below indicate the severity of the danger or equipment damage that may occur if a precaution or warning is ignored and the product is used incorrectly. This label indicates a danger of severe injury or even death. Warning Caution This label indicates a danger of injury, or equipment damage. The type of action associated with each precaution is indicated using the pictographs shown below (example pictographs). Unit fastening screws ( + M5-35) . x2 This pictograph indicates "Caution"--something you should beware of. This pictograph indicates a "Prohibition"--something you must not do. This pictograph indicates an "Instruction"--something you should always do. Insulation spacers . x4 Allen head countersunk screws (M8-50) . [. . . ] Fit so there is no contact between the attachment screws or power cord and any metal inside the wall. For the TV power supply plug, use a power supply outlet that can be reached easily. Ensure good air flow so that the equipment ambient temperature does not exceed 40°C. Failure to do this may cause heat to build up inside the plasma TV, resulting in malfunction. [. . . ]