User manual PANASONIC TZ-PCD3000

[. . . ] See Figure. IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus(including amplifiers)that produce heat. [. . . ] Do not install and use this unit standing on its side. FCC CAUTION: Pursuant to 47CFR, Part 15. 21 of the FCC rules, any changes or modifications to this Digital CATV Terminal not expressly approved by Matsushita Electric Corporation of America could cause harmful interference and would void the user's authority to operate this device. Care and Cleaning Turn Digital CATV Terminal Off For Digital CATV Terminal, avoid excessive moisture and wipe dry. Avoid bumping or scraping the Digital CATV Terminal. Remote Control For Remote Control, use a soft cloth dampened with water or a mild detergent solution. Do not use benzene, thinner or other petroleum based products. FCC Declaration of Conformity PANASONIC CONSUMER ELECTRONICS COMPANY Responsible party: Matsushita Electric Corporation of America One Panasonic Way Secaucus, NJ 07094 U. S. A. Telephone Number: 1-888-726-2377 (9 a. m. -9 p. m. , Mon-Fri, EST) (10 a. m. -7 p. m. , Sat-Sun, EST) or E-MAIL: consumerproducts@panasonic. com This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This product incorporates copyright protection technology thatb is protected by U. S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise autthorized by Macrovision. Reverse engineering or disassembly is prohibited. 4, 631, 603; 4, 577, 216; 4, 819, 098; 4, 907, 093; 6, 381, 747; and 6, 516, 132 Trademark acknowledgements Manufactured under license from Dolby Laboratories. "Dolby" and the double-D symbol are trademarks of Dolby Laboratories. "TVPASS CARD" is a trademark of MOTOROLA CORPORATION. All other trademarks are the property of the various trademark owners. FCC STATEMENT FCC INFORMATION Radio Interference This equipment has been tested and found to comply with the limit for a Class B Digital Device in accordance with the specifications in Part 15 of FCC Rules. The rules are designed to provide reasonable protection against radio and television interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or televisions reception (which you can determine by turning the equipment off and on), try to correct the interference by one or more of the following measures. Reposition or relocate the receiving antenna for the radio or television that is "receiving" the interference. Change the position of the Digital CATV Terminal with respect to the radio or television equipment that is receiving interference. Dear Panasonic Customer Welcome to the Panasonic Family of customers. We hope that you have many years of enjoyment from your new Digital CATV Terminal. To obtain maximum benefit from your set, please read these Instructions before making any adjustments, and retain them for future reference. [. . . ] (do not connect your PC to this SERIAL port. ) Use to connect the Digital CATV Terminal to an AC electrical outlet with AC cord (included). S-VIDEO OUT DIGITAL AUDIO OPT OUT 10 IR BLASTER 11 SERIAL port 12 AC Power Input 4 USB Port Serial (Universal Bus) Digital CATV Terminal connection to stereo TV and stereo VCR Follow this diagram when connecting the Digital CATV Terminal to a stereo TV. S-VIDEO VIDEO L AUDIO R INPUT Procedure 1 Connect S-VIDEO Cable from the S-VIDEO output jack on the Digital CATV Terminal to the S-VIDEO input jack on the TV or VCR. Note: Connect either the S-VIDEO or video input/output as shown above. S-VIDEO will provide better picture quallity. 2 Connect audio cables from the left and right audio output jacks on the Digital CATV Terminal to the left and right audio input jacks on the TV or VCR. [. . . ]