User manual PANASONIC UB5315

[. . . ] Installation performed by non-authorized individuals could cause safety-related problems with the operation of this equipment. · To locate the closest authorized dealer in your area, please call 1-800-449-8989. Thank you for purchasing the Panasonic Electronic Board. For optimum performance and safety, please read these instructions carefully. Accessories · · · · Markers (red, black, and blue) Operating Instructions . . 1 · · · · Letter size copy paper roll [10 m (32. 8 ft. )] Software CD-ROM . By way of example, this manual describes an Electronic Board which is used with the stand. [. . . ] It is also possible to start scanning using the Copy Key or 2-Screen Copy Key on the electronic board. Scanning You can scan images on the screen to your computer by operating Panasonic-DMS. 6 Click [Close] on the Panaboard Operation Panel to finish scanning. · About the Document Manager, refer to the Document Manager System operating instructions in the CD-ROM. 1 Click [Start], move the pointer to [Programs]­[Panasonic]­[Panasonic Document Management System]­ [Document Manager]. (For Windows XP, [All Programs] instead of [Programs]. ) · The Panasonic-DMS software runs. Note · Dragging the Panaboard Operation Panel or activating other software programs may cause scanning troubles. 2 Click the [File] menu, then click [Select Source. . . ]. 3 Select [Panaboard-UB5 USB TWAIN Driver] and click the [Select] button. 23 Computer Interfacing Panaboard Operation Panel It is possible to perform the same operations as with the electronic board control panel (page 9) from the following Panaboard Operation buttons. Note: While the Panaboard Operation Panel is displayed, the Copy Key and 2-Screen Copy Key on the electronic board control panel are used for scanning images into the computer. Panel Name Contrast Indicator Contrast Button 2-Screen Scan Button Multi-Copy/ Error Indicator Description This lamp indicator displays the contrast used during scanning or copying. Indicator off: Normal scanning or copying contrast Indicator on: Darker than normal scanning or copying contrast Each time this button is pressed, the unit will alternate between normal and dark contrast modes (Normal/Dark). This button scans the front and back of the screen on a single page. This indicator displays the number of copies to be made. The display changes each time the Multi-Copy/Stop Button is pressed. Example: 1 2 ··· 9 1 ··· When an error occurs, a flashing symbol will appear in this display to indicate the error status. (See page 29. ) Multi-Copy/ Stop Button When making multiple copies, press this button until the desired number of copies is displayed on the Multi-Copy/Error Indicator. This button can also be pressed while multiple copies are being made to stop the copying process. * During scanning, the setting 1 to 9 for the number of copies is ignored. Scan Button Advance Button 2-Screen Copy Button Copy Button This button scans the screen. This button advances the screen from right to left. This button causes the front and back of the screen to be copied on a single sheet of paper. · If you accidentally write on the board with an oil-based marker, wipe with a small amount of ethyl alcohol. Notes · Use a neutral kitchen cleaner diluted with water for hard-to-clean stains. (If you accidentally write on the screen with an oil-based marker, wipe with a small amount of ethyl alcohol. ) · Do not use thinner, benzine or cleaners containing abrasives as this may result in discoloration. · Do not wipe the screen film with a dry cloth as this may generate a static charge. Caring for the eraser When the erasing surface of the eraser becomes dirty, hold down the sheet under the top sheet with your finger and peel off the dirty sheet by pulling in the direction of the arrow. Note · When the eraser becomes thin, make sure that the corners of the eraser do not strike the screen during erasing as this may damage the screen. Cleaning the printer head and paper feed roller If black streaks appear on the copy, clean the printer head and the paper feed roller. 1 Door Open Button PUSH OPEN Push the door open button and open the printer door. 26 Daily Care and Maintenance 2 Clean the Printer Head Dampen the tip of a cotton swab in ethyl alcohol and gently wipe the printer head. Note · Never touch the printer head or the surrounding area with your hands as this may disable copying. Printer head (Gold) Cotton swab Operating Instructions 3 Paper feed roller Clean the Paper Feed Roller Wipe any dirt or stains off the paper feed roller. · Dampen a soft cloth with neutral kitchen cleaner diluted in water, wring the cloth thoroughly, and wipe the entire surface of the roller while rotating it. If this does not remove all dirt, wipe with a cloth dampened with ethyl alcohol. 4 Load the copy paper and close the printer door securely, using two hands. · For details on loading the copy paper, see page 10. 27 Troubleshooting Treat problems according to the information given in the table below. If problems still persist, call your dealer for service. Symptom Power switch is on but the indicator is off. Care and Remedy Check that the power plug is securely plugged in. (If the indicator still does not light, turn the power off and on again. ) The unit is out of copy paper. (The Error Indicator flashes " Load new paper. (The Error Indicator flashes " Close the printer door firmly until a click is heard. ". ) ". ) See Page ­ 10 10 Copied copy paper will not come out. Paper is jammed in the printer. Remove the jammed paper and cut off the wrinkled portion, then load paper again. Open the printer door and wipe the paper feed roller to clean it. [. . . ] *1 A screw (short) is used for the stopper screw of step 15 on page 37. Before assembly, be sure to lock the casters. Locking the casters (Push this side) Releasing the lock 42 Assembly 1 Assembling the stand Assembling the fall-prevention extension legs The fall-prevention extension legs are effective in increasing the safety of the electronic board. Fall-prevention extension legs · Caster locks are attached to the back side. Caution · Install and always set the fall-prevention legs when using the stand. · When tightening the screws , hold the nut with pliers. Assembling the stand Slide sheet Installation Manual Side pipe Reinforce pipe Slide sheet Base pipe Extension pipe S Base pipe · Assemble the side pipes with the slide sheets facing inside. 43 2 Assembling the board attachment frame Stamp "UL" Board attachment (upper) Stamp "UR" Slide plate (left) Stamp "LL" Stamp "LR" Slide plate (right) Board attachment (lower) · The board attachments (upper and lower) are supplied with the electronic board. · Place the board attachments and the slide plates with their stamps facing up and assemble them matching their same stamps. 3 Attach the board attachment frame to the stand. Step E Step D Height adjustment handle Cap Step B Step D Side pipe Step A Screw Slide plate Fixing plate Step A Height adjustment handle Side pipe Step C The caster locks are attached to the back side. [. . . ]