User manual PANASONIC UE-608031

[. . . ] Operating Instructions Up/Down Wall Mount Kit Up/Down Stand Kit (For elite Panaboard) Model No. UE-608030 UE-608031 UE-608032 Installation Manual Included (for qualified service personnel) · To assemble this unit, please refer to the Installation Manual on pages 14 through 39. · Before operating this unit, please read these instructions completely and keep them carefully for future reference. · This unit is designed for installation by a qualified servicing dealer. Installation performed by non-authorized individuals could cause safety-related problems with the operation of this equipment. [. . . ] To ensure that the work is accomplished safely and properly, make it a basic rule to strictly observe all other applicable aspects of safety control. -- If there is a chance that the unit has ended up being deformed or damaged by unexpected impact while it was being transported and installed, do not install it without taking appropriate measures. Otherwise, it may fall off the wall. 18 Installation Manual Wall Mounting Construction 2 Concerning Installation · The up/down stand kit and up/down wall mount kit are for indoor use. Neither can they be installed or used in the following kinds of places. -- Places where they will be directly exposed to rain or water (including under the eaves of a house) -- Places where chemicals are used such as swimming pools -- Places with a lot of steam or grease such as manufacturing plants or kitchens, places with special environments such as those with combustible atmospheres -- Seaborne or coastal places and places where corrosive gases are given off -- Places subject to frequent vibrations such as in vehicles or ships (the up/down wall mount kit is not designed to be used in or on vehicles) -- Places other than walls (this is applicable to the up/down wall mount kit) -- Places where the operating temperature range of the elite Panaboard will be exceeded · To prevent deformation and discoloring, avoid installing the kits in places exposed to direct sunlight or near heating or cooling appliances, etc. · When carrying out the work, be absolutely sure to abide by the construction-related laws and other related ordinances of the country concerned. Concerning the Installation Surface · Mount the up/down unit in a stable location. The specified pull-out strength is required per anchor. M8 anchor bolts are used when installing the up/down unit on the wall. (Specified pull-out strength: 5, 197. 5 N [530 kgf]) · Avoid mounting the unit on a wall, which is not a principal structure component*, with a plasterboard, plywood or other such construction since these walls are weak. If mounting on such a wall is unavoidable, reinforce the wall adequately (by ensuring that its ultimate strength will be at least as great as the specified pull-out strength of the anchors). *Principal Structural Component This term refers to walls, pillars, floors, beams, roofs and staircases, and it excludes partition walls, stud walls, attached columns, raised floors, floors on the bottom-most levels of buildings, floors of revolving stages, secondary beams, pent-roofs, partial sub-staircases, outdoor staircases and other structural parts of a similar nature which are not crucial to the building from a structural point of view. Concerning the Screws and Bolts Used · When obtaining anchors and bolts locally, be absolutely sure that they satisfy the required specifications. Concerning the Tightening of the Screws and Bolts · Tighten the screws and bolts using the specified torque. Tightening them up using excessive torque will damage the screw threads, causing the unit to fall off the wall. Conversely, the screws will be loose if they are tightened up with insufficient torque. · The torque levels are specified, so use a torque driver to tighten up the screws and bolts. · The range in which the torque can be specified is limited for each torque driver. Refer to the recommended torque levels which are specified, and use the appropriate torque driver. · Do not use an impact driver or power driver whose torque is difficult to control since using such a driver may damage the screws and bolts. · Tighten the screws and bolts so they go straight in. Other Checkpoints · Make sure that the location is large enough to accommodate the elite Panaboard. [. . . ] (When the UB-T781, UB-T781W, UB-T780 or UB-T780BP is installed) Nut A Nut B 11 Holding nut B in place with a 10 mm ( /32 in. ) wrench, use another wrench to loosen nut A (counterclockwise, 5). 13 7 14 Mount the elite Panaboard on the up/down unit again. Nut A Nut B 5 32 Installation Manual Wall Mounting Construction Mounting the elite Panaboard 1 Align the wall mount holes on the bottom of the board attachments with the left and right positions of the board bottom bracket (loosely secured to the up/down unit) and secure them tightly using the board mounting screws (5, two on each side). For UB-T880 Checking the Up/Down Operations · Confirm that the up/down part can easily be lifted higher than the pin end stopper. · Confirm that the up/down part does not drop more than 20 cm (7 7/8 in. ) of its own accord when released from the highest point. At this stage, check up/down operations, and if they are not balanced, remove the elite Panaboard and readjust the up/down unit. · Check that none of the cables are stretched to their full length or sandwiched when the up/down operations are performed. Lower Frame Cover Board Mounting Screws (5) 2 Try drawing the elite Panaboard toward you, and check that the elite Panaboard is fastened securely to the up/down unit. · Confirm that the elite Panaboard is securely attached and does not move freely back and forth. Installation Manual 33 Wall Mounting Construction Wiring Connections 1 Position the computer which you are going to use at the prescribed location, and connect the computer, projector and elite Panaboard as shown below. Projector Power Cable 1 Apply the High-Temperature Warning Label 1 2 Turn on the power of the computer, projector and elite Panaboard in this order. [. . . ]