User manual PANASONIC VLG201CE

[. . . ] Video Intercom System Installation and Operation Guide Model No. VL-G201 Thank you for purchasing a Panasonic Video Intercom System. Please read this Installation and Operation Guide before using the unit and save for future reference. Table of Contents Important Information Important safety instructions . 7 Introduction and Installation Included items . 27 Using the Unit Turning {PBX MODE} switch ON/OFF . [. . . ] This may cause communication errors or malfunction. L Do not install the monitor station inside a wall. 14 Introduction and Installation Wiring schematic diagram Door station Terminal box (4-conductor wiring) D1 D2 PBX (Non polar) Monitor station D1 D2 P1 P2 S1 S2 (Non polar) Door (Door Opener) (Non polar) Power cable AC adaptor Power cord Note: L The Door Opener wiring schematic diagram is an example. Refer to the wiring instructions provided with your Door Opener and PBX for details. L Refer to the technical data on page 38 when connecting to a Door Opener. Power cable/wire type and distance L Power cable (between the monitor station and the AC adaptor): Type: 1. 2 Fire alarm cable 16 AWG Distance: Maximum 30 m L Wire (between the monitor station and the door station): Type: General cable CAT-3 24 AWG Distance: Maximum 100 m Loop resistance: 18. 4 or lower L Wire (between the monitor station and PBX): Type: General cable CAT-3 24 AWG Distance: Maximum 100 m 15 Introduction and Installation Installing the door station Make sure to install the door station on a flat, vertical wall. Important: L On the bottom surface of the door station, there is a hole to allow water to drain. Do not cover it up when installing. 1 Unscrew the hex-head screw using the longer end of the allen key and remove the mounting bracket from the rear of the door station. L The pin hole camera is not a screw to be touched or removed. Mounting bracket Pin hole camera Hex-head screw (Attached to the door station) Allen key 16 Introduction and Installation 2 Attach the mounting bracket to the wall using the wood screws (3. 8 mm x 20 mm). L Before drilling, see page 13 for installation location. Mounting bracket 83. 5 mm Wood screws Wall Wire (Not included) 3 Connect the wires that connect to the monitor station to the terminal connector by unscrewing the screws, pushing in the wires, then tightly fastening the screws. L See page 15 for the wire type and distance. L You can change the camera angle using the camera angle control lever. See page 13 for details. Terminal connector (Non polar) Camera angle control lever Screw Wire (Not included) 17 Introduction and Installation L If you want to connect the wires without them passing through a hole in the wall, connect the wires by passing them through the ribs and the wire hole. Rib Wire hole 4 Mount the door station to the mounting bracket. 1 2 Push the door station down until it is secure. 18 Introduction and Installation 5 Insert the hex-head screw using the longer end of the allen key. Hex-head screw Allen key 6 Attach the bolt cover using the shorter end of the allen key. L Use protrusion on the shorter end of the allen key to rotate the bolt cover until it is secure. Allen key 19 Introduction and Installation Installing the monitor station Note: L When connecting to a PBX, make sure the {PBX MODE} switch is set to {ON} before installing the monitor station (page 28). 1 Install the mounting bracket to a wall using the wood screws (4 mm x 16 mm). L Remove the mounting bracket from the rear of the monitor station beforehand. L Before drilling, see page 13 for installation location. Mounting bracket 83. 5 mm Wood screws Wall Wire (Not included) 2 Attach the power cable to the terminal. See page 26 for details on how to attach the power cable. L If you want to use your own power cable, see page 15 for the type and distance. Terminal (Non polar) Power cable 20 Introduction and Installation 3 Attach the wires that connect to the door station to the terminal. See page 26 for details on how to attach the wires. L See page 15 for the wire type and distance. L See the wiring schematic diagram on page 15. Stripped end of the wire 9 mm Terminal (Non polar) Button Wire (Not included) Power cable L If you want to connect the wires and the power cable without them passing through a hole in the wall, connect by passing the wires through the wire guide, and the power cable through the power cable guide. Power cable guide Wire guide 21 Introduction and Installation 4 Mount the monitor station to the mounting bracket. 1 2 Push the monitor station down until it is secure. 5 Take out the AC adaptor and the DC terminal from the case. L Push the arrow mark on the front case, then release from the rear case. L Take out the cardboard and wood screws. [. . . ] Only while you press {TALK}, the outside visitor can hear your voice. L You talked for more than about 3 minutes in {HOLD} mode. The maximum display time is approximately 3 minutes. The display is white, or black or white lines are shown on the display. The colour of the display is different from the actual colour. [. . . ]