User manual PANASONIC VLGM201A

[. . . ] Single Monitor Station Installation and Operation Guide Model No. VL-GM201A Thank you for purchasing a Panasonic Single Monitor Station. Please read this Installation and Operation Guide before using the unit and save for future reference. Table of Contents Important Information Important safety instructions . 5 Introduction and Installation Included items . 19 Using the Unit Turning {PBX MODE} switch ON/OFF . [. . . ] This may cause communication errors or malfunction. L Do not install the monitor station inside a wall. 10 Introduction and Installation Wiring schematic diagram Door station Terminal box (4-conductor wiring) D1 D2 PBX (Example: KX-TDA50) (Non polar) Monitor station D1 D2 P1 P2 S1 S2 (Non polar) (Non polar) Power cable AC adaptor Power cord Door opener Note: L This door opener wiring schematic diagram is only an example. Refer to the wiring instructions provided with your door opener and PBX for details. L Refer to the technical data on page 30 when connecting to a door opener. L For details on how to attach the power cable, see page 18. DC terminal AC adaptor Power cord 3 To AC outlet 2 Power cable 1 7 Attach the DC cord to the clamp on the rear of the DC terminal. L This will help to avoid the DC cord to disconnect from the DC terminal. DC terminal DC cord Clamp 15 Introduction and Installation To attach the AC adaptor and the DC terminal to a wall By placing the AC adaptor and the DC terminal in the case and mounting the case to the wall, you can protect the AC adaptor and the DC terminal from tampering and exposure. Note: L Disconnect the DC cord from the clamp on the rear of the DC terminal beforehand. L Take out the cardboard and wood screws from the AC case beforehand. 1 Attach the rear part of the case to a wall using the wood screws (4 mm x 16 mm, 3/16'' x 5/8''). Case 83. 5 mm (35/16") Wood screws Wall 2 Pack the AC adaptor and DC terminal as shown. LBe sure to run the power cord through the power cord hole. LBe sure to bundle the DC cord so that it will not touch the bottom of the case. LBe sure to run the wires through the wire hole, then under the wire rib. Wire rib 3 DC terminal Wire hole 2 DC cord 1 AC adaptor Power cord hole Power cord 16 Introduction and Installation 3 Attach the front of the case. 1 2 Note: L To open the case again, push the bottom of the front case, then release from the rear case. 17 Introduction and Installation To attach the power cable Monitor station DC terminal Button Button Terminal connector Terminal connector L While pressing on the button with a pointed object such as a screwdriver, insert the power cable into the terminal connector. L To disconnect the power cable, press on the button while pulling out. L To attach an optional power cable, cut off about 12 mm (1/2") of the cable cover (1), then push in firmly until the end of the cable is securely inserted into the power connection terminal (2). 1 2 Power cable cross section 12 mm (1/2") Correct Incorrect To attach the wires Button Terminal connector L Strip off of the wire cover so that about 9 mm (3/8") of the wire is exposed. L While pressing on the button with a pointed object such as a screwdriver, insert the wire into the terminal connector. L To disconnect a wire, press on the button while pulling out. 18 Introduction and Installation Using the desktop stand (Optional) You can place the monitor station on a desktop. See page 7 for optional item information. Wood screws Wire Mounting bracket Desktop stand Power cable Note: L If you previously connected the power cable through the power cable guide (page 13), remove the power cable from the power cable guide of the monitor station beforehand, then attach to the desktop stand. 19 Using the Unit Turning {PBX MODE} switch ON/OFF When connecting to a PBX (page 22), turn {PBX MODE} switch on. The default setting is {ON}. 1 Remove the switch cover from the rear of the monitor station. L Use a sharp, thin object such as a mechanical pencil. Switch cover 2 Select {ON} (default) or {OFF}. PBX MODE OFF ON {PBX MODE} switch 20 Using the Unit 3 Attach the switch cover to the rear of the monitor station. Switch cover 21 Using the Unit Connecting to a PBX Connecting to a PBX allows you to answer door calls from any telephone. See page 7 for the PBX model list that is compatible and other optional hardware. Important: L Make sure {PBX MODE} switch is set to {ON} beforehand (page 20). The default setting is {ON}. PBX MODE OFF ON {PBX MODE} switch Note: L If you answer a call from the door station with a PBX extension, the camera image from the door station will be displayed at the monitor station. [. . . ] The display will not display anything or no voices can be heard. The monitor station does not ring. I cannot talk to the visitor or the ringer tone rings regularly. Sound cuts in/out or fades. {AUTO} mode does not operate properly. Your voice cannot be heard by the outside visitor. The outside visitor complains the door station does not beep when the call button is pressed. 28 Help Problem The display turns off during a conversation (Sound continues). [. . . ]